Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
+ 4.1. Engine OHV (with a camshaft in the block of cylinders)
+ 4.2. Engines OHC
+ 4.3. Engine DOHC with 16 valves
+ 4.4. Diesel engines 16D and 16DА
- 4.5. Diesel engines of 1,7 l
4.5.1. A technical characteristics
4.5.2. A method of removal of the engine
4.5.3. Engine repair
4.5.4. Replacement of engine oil and the oil filter
- 4.5.5. Check, removal, installation and adjustment of a gear belt
4.5.5.1. Engines 17D
4.5.5.2. Engines 17DR
4.5.6. Check and adjustment timing
4.5.7. Removal and installation of a head of the block of cylinders
4.5.8. Removal and camshaft installation
4.5.9. Removal and installation of the oil pallet
4.5.10. Removal and installation of the oil pump
4.5.11. Removal and installation перепускного the valve
4.5.12. Removal and installation of the water pump
4.5.13. Removal, check and thermostat installation
4.5.14. Removal and installation of pistons and rods
4.5.15. Removal and flywheel installation
4.5.16. Replacement of sealing rings
4.5.17. Replacement of support of the power unit
4.5.18. Engine removal
4.5.19. Engine repair
4.5.20. Removal, repair and assemblage of the oil pump
+ 4.5.21. A head of the block of cylinders
4.5.22. Check of elements of the engine
4.5.23. Engine installation
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes
|
Installation of a gear belt
And – to pull a belt,
In – to weaken a tension of a belt,
1 – a direction of rotation,
2 – an aperture,
3 – the highest point of the lift of the valve of a cam №2,
4 – labels of the fuel pump for installation of the piston №1 in ВМТ, |
|
5 – labels of a flywheel for installation of the piston №1 in ВМТ,
6 – кив натяжителя,
7 – the pulley index натяжителя,
8 – an adjusting label of a pulley натяжителя,
9 – an adjusting label of the water pump,
10 – an adjusting label of the block of cylinders |
Automatic натяжитель a gear belt
And – ledges on the water pump and the block of cylinders,
In – the index натяжителя is combined with a cut in an arm натяжителя, |
|
1 – turn the lever натяжителя counter-clockwise to weaken a tension of a belt,
2 – turn the lever натяжителя clockwise to pull a belt |
Check
PERFORMANCE ORDER |
1. Remove a wire of weight from the accumulator. |
2. Remove auxiliary приводные belts and the air filter. |
|
3. Remove the top casing of a gear belt. |
4. Examine a gear belt on presence of damages and pollution. If necessary replace a belt. |
|
5. Unscrew bolts and remove a pulley of a cranked shaft. |
|
6. Remove the bottom casing of a gear belt (bolts of fastening of the bottom casing of a gear belt are specified by arrows). |
|
Removal, installation and tension adjustment
PERFORMANCE ORDER |
1. Look the corresponding description in subsection 4.4.5, but consider that you do not need to weaken bolts of the water pump and to rotate the pump as the belt tension is regulated automatically. |
|
2. Unscrew a bolt натяжителя a belt and turn the lever натяжителя to weaken a belt tension. Fix натяжитель in such position, having tightened a bolt. Remove a gear belt. |
3. Check up, that the ledge on a flange of the water pump has been combined with a corresponding ledge on the block of cylinders. If necessary adjust position of the water pump (fig. Installation of a gear belt see). |
4. Pull a gear belt, having weakened a bolt натяжителя and having turned the lever натяжителя counter-clockwise against the stop. Tighten a bolt натяжителя. |
5. Turn a cranked shaft on two complete revolutions and check up that adjusting labels are combined with indexes. |
6. Again ослабьте a bolt натяжителя also turn the lever натяжителя so that to combine the index натяжителя and a cut in an arm натяжителя (see fig. Automatic натяжитель a gear belt). Tighten a bolt натяжителя. |
|
|
On the main page
|