Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

12.14. The door lock

THE GENERAL DATA

Door-lock, draught of the lock in assemblage / the lock cylinder in assemblage

1. A lock control lever 2. Draught of lever transfer of the lock At removal disconnect the lock 3. A control lever clip 4. A plastic washer 5. 16 Н.м. 6. A konusnaja washer Two can be established конусные washers if it is necessary for adjustment 7. A bolt запорной door-lock plates, 50 Н.м. 8. The door lock 9. A rope, for work in a door

10. Clips, watch a direction of the main draught in a clip 11. A condensing lining 12. A fixing plate of draught of the lock 13. A rotary clamp For removal зажиа to turn on 65 ° 14. 3 Н.м. 15. The door handle 16. An external plate of the lock 17. Draught of lever transfer of the lock, the lock cylinder Pay attention that draught is attached with the help шарнирной plugs

Door-lock

1. A bolt with a cylindrical head, 3 Н.м. 2. The door handle 3. The lock cylinder Remove only by means of a key 4. A condensing ring 5. A plate

6. A spring 7. A control lever with the loose leaf 8. The S-shaped clamp 9. A lock clamp For removal to turn on 65 °

Door-lock

Removal

PERFORMANCE ORDER

1) remove the decorative panel of a forward door 2) disconnect a clip of draught of lever transfer and extend draught 3) disconnect a rope 4) pull out a door-lock from knot 2 5) remove a lining 3

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER

1) again to connect a rope, pull the lever 4 in an arrow direction; insert a screw-driver into an aperture 5 to establish a rope into place 2) screw up all bolts with the moment 16 Н.м.

The door lock in assemblage (Compartment model)

1. An external plate of a door-lock 2. The door handle 3. A washer 4. A bolt with a head under a face key 5. Draught of the lock – the lock cylinder At снятиии displace the rotary plug 6. A rope 7. Clips Watch a direction of the main draught in a clip 8. Draught of the lock 9. The door lock 10. A screw with a crosswise head 11. A fixing plate of draught of the lock

12. A bolt, 16 Н.м. 13. A clamp 14. A clamp substrate Can be established more than one 15. A condensing lining 16. A door-lock 17. The self-cutting screw with плоскоконической a head, 16 Н.м. 18. A clamp for a control lever Press on муфту to remove draught of lever transfer of the lock 19. Draught of the lock 20. Draught of a control lever of the lock 21. The door-lock button 22. A rotary clamp

The door lock (Compartment model)

Removal

PERFORMANCE ORDER

1) remove the decorative panel of a forward door 2) disconnect a clip of draught of lever transfer and extend draught 3) disconnect a rope 4) pull out a door-lock from knot 2

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER

1) connect a rope, having pulled the lever 4 in a direction specified by an arrow 2) place a screw-driver in an aperture 5 to establish a rope into place 3) screw up all bolts with the moment 16 Н.м.

Door-lock cover, removal

PERFORMANCE ORDER

Disconnect a cover from a door covering

Door-lock cover, installation

Installation carry out upside-down.

Decorative covering of the handle of the lock, removal

---

The prevention

The decorative covering of the handle of a door should be removed before removal of the handle not to admit damage of the painted surface of a decorative covering.

---

PERFORMANCE ORDER

1) lift the door handle 2) pull out the lock probe in a direction specified by an arrow 3) remove a decorative covering

Door-lock (models of the Compartment since 1990 modelling years)

1. An adjusting detail Squeezing the lever on a carving and it can be adjusted through a fixing aperture 2. A lock aperture 3. The door lock 4. 16 Н.м. 5. A plastic washer 6. A konusnaja washer Two can be in case of need established конусные washers 7. A pin of a latch 50 Н.м. 8. A rope for the internal lock of a door

9. A clamp Pay attention to position of a rope in clamps 10. A clamp For a clamp detachment remove a rope and turn a clamp on 90 ° 11. An extending clamp 12. The sharnirnyj lever 13. Draught of the lever mechanism 14. A condensing lining 15. A rope of the lock of a door 16. The door handle 17. An external covering of the handle of a door 18. 3 Н.м.

The door lock (models of the Compartment since 1990 modelling years)

Removal

PERFORMANCE ORDER

1) remove the decorative panel of a forward door 2) turn the lever 1, having pulled a rope in a direction specified by an arrow, and supporting in the necessary position by means of a screw-driver through an aperture 2 3) disconnect a rope 4) unscrew bolts 5) pull out the lock of a door from a clamp 3, sealants 5

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER

1) attach a rope 2) insert the door lock into a clamp 3) combine the handle of a door with the lock 4) adjust, as it is required 5) direct приводной the mechanism 4 in приводной the lever of the lock of a door; this operation can be observed through an aperture for access