Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
- 12. A body, salon
   12.2. The central section of a guard
   12.3. A cowl rope
   12.4. A forward guard
   12.5. A forward wing
   12.6. Lock pins of a cowl, the rubber shock-absorber
   12.7. A cowl
   12.8. A gazonapolnennaja rack (models the Sedan)
   12.9. A luggage carrier cover
   12.10. A back door (Compartment model)
   12.11. A forward door, the bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing stoppers, a window regulator
   12.14. The door lock
   12.15. Draught of lever transfer of the lock
   12.16. A rope of an internal door-lock
   12.17. A rotary clamp, an adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. The central lock
   12.21. The pump with two modes of forcing
   12.22. The leading activator
   12.23. The activator of a back door
   12.24. The activator of a cover of a luggage carrier
   12.25. The activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt overlay (Compartment model)
   12.28. A skeleton of a back door, the bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. A rope, шарнирный the lever
   12.31. The door handle
   12.32. The holder of components of a door
   12.33. The hatch
   12.34. A bumper casing
   12.35. Hermetic sealing of a back bumper
   12.36. An extending clamp
   12.37. A forward spoiler / a lining of a niche of a wheel (Compartment model)
   12.38. The top overlay of a forward spoiler (Compartment model)
   12.39. A back spoiler / a lining of a niche of a wheel
   12.40. A back bumper (Compartment model)
   12.41. window raiser
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. A central air
+ 14. An electric equipment

12.34. A bumper casing

THE GENERAL DATA

Forward bumper, assemblage

1. 30 Н.м.
2. 23 Н.м.
3. An absorber of shock loading
4. A bumper crossbeam
For removal it is necessary to remove a bumper casing
5. The central decorative
Strip
Removal: pull out from under fixing pads (the bumper should be disassembled, and the crossbeam is removed)
6. A broad nut
7. A towing hook
8. The marked apertures 9. The holder of licence plate
10. Bolts М5x12
11. Decorative facing (5 cylinders)
12. Decorative facing (4 cylinders)
13. A bumper casing
14. An extending clamp
15. A plastic nut
16. A rubber washer
17. A decorative strip
18. A cover
19. An arm
20. 30 Н.м.
21. Directing

Bumper casing, removal

PERFORMANCE ORDER

1) remove extending fixing agents (insert)

2) disconnect from directing and press on the ends in a direction downwards (an arrow

3) remove a cover from a decorative strip and unscrew bolts

4) disconnect fixing pads from a bumper crossbeam

5) decorative facing remove in a direction specified by an arrow In

Towing hook, installation

1. A rivet

2. Прекладина

3. Кроншейн the towing hatch

Arm, installation

1. A crossbeam

2. A rivet

3. An arm

On all-wheel drive models the left absorber of shock loading fastens to a cross-beam an additional bolt. Tighten this bolt till the moment 23 Н.м.

Forward bumper, assemblage (Compartment model)

1. A bolt with шестигранной a head, 23 Н.м.
2. A washer
3. A blow absorber
Removal: remove a bumper
Unscrew bolts with шестигранной a head
4. A washer
Three washers on each absorber
5. Bolts with шестигранной a head, 23 Н.м.
6. A washer
7. A bolt with плоскоконической a head, 23 Н.м.
8. A spoiler
Removal: remove a bumper
Remove extending clamps
Unscrew a spoiler from a wheel niche
Unscrew the top fixing bolts on a spoiler
Disconnect washers of forward headlights if they are established
Remove a spoiler, having pulled out it directly from a body
9. An antifog headlight
If it is established, there is necessity no it to remove during spoiler removal
10. A bumper crossbeam
For removal it is necessary to remove first of all a casing of a bumper and a decorative covering
11. A decorative strip
12. A bumper casing
It is possible to remove after the bumper will be disconnected
13. The Bolt / a washer 6 Н.м.
14. An arm
In an installation time the spoiler is necessary for establishing on an arm
15. The Bolt / a washer 6 Н.м.
16. A washer
17. A screw 1,0 Н.м.
18. The self-cut screw with плоскоконической a head
19. The holder of licence plate
20. A nut
21. A washer
Remove a bumper
From within unscrew bolts with шестигранной a head
In front remove a washer jet
22. A shestigrannaja nut
крепит a jet of a washer of a headlight

On the main page