Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

12.18. Adjustment of doors

THE GENERAL DATA

Adjust a backlash, displacing door loops And = 5 + 1 mm b = 5.5 + 1 mm Level height with a case line

Adjustment place – loops (very big apertures on a loop in a place where it joins a forward / central rack of a body).

To avoid noise from air, regulate on assembly loops or in a back part of doors on a pin запорной plates.

Sections А–А, В–В, С–С:

With = 0.5 + 0.5 mm

Section D–D:

d = 14.5 mm

Door backlash, adjustment

PERFORMANCE ORDER

1) having unscrewed bolts 1, unscrew the plug with the cutting, being behind bolts until it will not cease to adjoin to a forward rack of a body 2) ослабьте bolts 2, close a door and adjust a backlash, moving a door And = 5 + 1 mm 3) ослабьте or tighten by means of a wrench 4) screw up the plug with cutting until it will not contact with a forward rack of a body 5) screw up bolts and clamp them with the moment 30 Н.м. 6) check up a backlash

Height adjustment

PERFORMANCE ORDER

1) ослабьте bolts 1 and 2 2) ослабьте or tighten by means of a wrench 3) move door loops 4) tighten bolts; 30 Н.м. 5) ослабьте bolts (arrows), also displace a door in the necessary direction 6) tighten bolts; 30 Н.м.

Prevention of noise from a wind

1 – a screwed detail of carving connection 2 – a washer with чашеобразной dredging 3 – a washer

Two washers with чашеобразной dredging can be in case of need used.

PERFORMANCE ORDER

1) adjust a screwed detail of carving connection of a latch in a back part of a door 2) a screwed detail of carving connection 50 Н.м.

Doors, adjustment (Compartment model)

PERFORMANCE ORDER

1) adjust a door backlash, displacing door loops 2) establish door height (a body contour). Adjustment is made on loops (very big apertures on a loop in a place where the loop fastens to a forward rack of a body) 3) for prevention of occurrence of noise from a wind regulate assembly loops of a door or in a back part of a door on запорной to a plate 4) ослабьте bolts 2, 4 by means of a wrench 5) unscrew the plug with cutting on bolts 2 from a forward rack of a body 6) close a door and displace it for backlash adjustment 7) twist the plug with cutting 3 until will be contact to a forward rack of a body 8) screw up bolts and tighten them with the moment 30 Н.м. 9) once again check up a backlash

Height adjustment

PERFORMANCE ORDER

1) ослабьте bolts 2, 4 by means of a wrench 2) unscrew the plug with cutting on bolts 2 from a forward rack of a body 3) close a door 4) displace door loops 5) tighten bolts with the moment 40 Н.м.

Noise from a wind in a forward part of a door, prevention

PERFORMANCE ORDER

1) ослабьте bolts 1 2) displace a door as it is required 3) tighten bolts 30 Н.м.

Noise from a wind in запорной to a plate, prevention

PERFORMANCE ORDER

Adjust a clamp pin in a back part of a door Pin of a clamp 16 Н.м. 1 – a clamp pin 2 – a shock plate 3 – a substrate For achievement of exact adjustment can be established more than one

Door backlash, adjustment (models of the Compartment since 1990 modelling years)

PERFORMANCE ORDER

1) having unscrewed bolts 1, unscrew the plug with cutting until it will not cease to adjoin to the central rack of a body 2) ослабьте bolts 2, close a door and adjust a backlash, displacing a door And = 5 + 1 mm 3) open a door and tighten bolts 2 with the moment 30 Н.м. The prevention Unscrew or screw up, using a key 2598. 4) twist plugs with a carving 3 until they will not adjoin to the central rack of a body 5) screw up bolts, 30 Н.м. 6) check up a backlash

Door height, adjustment

PERFORMANCE ORDER

1) ослабьте bolts 1 and 2 The prevention Unscrew or screw up, using a key 2598. 2) displace door loops in very big apertures 3) tighten bolts with the moment 30 Н.м.

Noise from a wind, elimination

PERFORMANCE ORDER

1) ослабьте bolts of a forward door (arrow), displace a door in grooves of loops 2) distance between a skeleton of a door and the central rack of a body d = 14.5 mm 3) tighten bolts with the moment 30 Н.м.

Back door, elimination of noise from a wind

1 – a shock washer 2 – a washer with чашеобразной dredging Two washers with чашеобразной dredging can be in case of need established.

Adjustment of a pin of a clamp of the lock of a door allows to eliminate noise in a back part of a door.

PERFORMANCE ORDER

1) adjust a clamp pin 2) 50 Н.м.