Audi A3

Since 1997 of release

Repair and car operation



Audi A3
- The maintenance instruction
   Cars of mark Audi A3/S3 - the summary
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, the tool and the workplace equipment
   Поддомкрачивание and towage
   Start of the engine from the auxiliary power supply
   Checks of readiness of the car to operation
   Automobile химикалии
   Diagnostics of malfunctions of knots and car systems
   Controls and receptions of safe operation
   Arrangement of controls and devices
   Keys, locks of a body with uniform management and the security alarm system
   Electric window raiser and rear-view mirrors
   Safety systems. Transportation of children
   Seats
   Luggage carrier
   Adjustable steering column
   Manual brake
   Automatic transmission
   The device of the acoustic help at a parking
   The lock of ignition and engine start
   Control and measuring devices. Precautionary and diagnostic systems
   The travelling computer
   Switches and switches
   Темпостат
   Screen wipers and washer
   Ventilation, heater and the conditioner of air of salon
   The podemno-sdvizhnaja panel крыши*
   Salon and luggage carrier illumination
   The salon equipment
   Luggage carrier on a roof
   Обкатка
   Features of driving of the car and auxiliary systems (ABS, EDS, ASR, ESP)
   Trailer operation
   Fuelling and emergency unlocking of a cover refuelling лючка
   Cowl
   Readjustment of headlights
   The first-aid set
   Sign on an emergency stop
   The complete set of the tool and jack
   Spare wheel
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release of the fulfilled gases
+ Engine electric equipment
+ Manual box of a gear change
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electroschemes


https://www.youtube.com/channel/UCoah5uA-uF-j35-MalVTfRQ


Control and measuring devices. Precautionary and diagnostic systems

THE GENERAL DATA

Control panel

1 – a tachometre and a digital watch with date indication
2 – control lamps
3 – the button of adjustment of hours / the control button
4 – temperature of a cooling liquid
5 – the index of a stock of fuel
6 – the display
– Indication of periodicity of maintenance service
– Alarm symbols
– External temperature
– Lever positions селектора*
– Information system водителя*
7 – the dump button
Run measuring instrument
Indications of periodicity of maintenance service
8 – a speedometer with the display panel
The counter of the general run
Run measuring instrument

1 tachometres and digital watch with date indication


Tachometre

The red sector of a scale corresponds to a range of the maximum turns, admissible is short-term for обкатанного and the heated-up engine.

It is recommended, however, most later at achievement by an arrow of the given sector of a scale to be switched to the raised transfer or to reduce gas.

During the period обкатки avoid высокооборотных modes.

Digital watch with date indication


The display panel of hours is in limits of a scale of a tachometre.

The top indication shows time, and bottom date.

The adjustment button establishes time and date. Hours can work as radio-controlled quartz *, and as a usual quartz watch.

At reception of the important radio information hours are included automatically into a mode “a radio-controlled quartz watch” with occurrence on the display panel of a symbol of reception of radio information (radio tower). In the absence of the important radio information within three days hours are automatically switched in a mode "quartz watch". Indication of a symbol of reception of radio information Thus disappears.

Installation of time of hours / dates

Manually time and date can be established only in a mode "quartz watch".

For installation of current hour
pull the button, hour indication yet will not start to blink. Indication of hour changes button turn to the left / to the right.

For installation of minutes
pull the button some times, indication of minutes yet will not start to blink. Indication of minutes changes button turn to the left / to the right.

For installation
of calendar date pull the button some times, indication of day, month or year yet will not start to blink. Indication of day, month or year changes button turn to the left / to the right.

The termination of a blinking of indication after отпускания buttons means end of process of installation.

Time zone installation

At moving on the car in other time zone accordingly change indication of hours.

For time zone installation (in a mode of radio hours) pull the button, hour indication yet will not start to blink. Time zone indication (current hour) changes button turn to the left / to the right.

Conclusion to indication of calendar date

Pull the button some times, indication of calendar date yet will not start to blink.

Calendar date is deduced on indication by button turn to the right and disappears at button turn to the left. The termination of a blinking of indication after отпускания buttons means end of process of installation.

2 control lamps

Address to the description more low.

3 button of adjustment of hours / the control button


The control button has following appointment:

Call of indication of the remained quantity of kilometres before maintenance service
Short-term pressing of the button at the included ignition on indication deduces quantity of the kilometres which have remained before maintenance service. Check of work of system can be carried out both at muffled, and at the working engine and at speed no more than 5 km/h.

For more detailed data address to the description more low.

The control of indication of symbols

Double pressing of the control button at the included ignition makes a consecutive call on indication of all symbols. Check of work of system can be carried out both at muffled, and at the working engine and at speed no more than 5 km/h.

In the presence of malfunction of 1st degree priority (a red symbol) the indication control is impossible.

Conclusion to indication of instructions водителю1)

At a blinking of any symbol of 1st degree priority, as the help to the driver on the display corresponding instructions can be deduced.
For example: “MOTOR ABSTELLEN, ЦLSTAND PRЬFEN” (muffle the engine, check up oil level).

1) Only cars with information system of the driver.

For выcandlesивания press the control button. Indication dies away approximately in 5 seconds after отпускания buttons.

Illumination of counters of run and hours

At the switched off ignition press the control button – approximately within 15 seconds counters of run and hours are shined.

Besides, illumination joins and burns within 30 seconds after opening of a door of the driver.

The button of adjustment of hours


Address to the description more low.

4 temperature of a cooling liquid

The index works at the included ignition.

Interval of temperatures of the cold engine

While the arrow is in the left part of a scale, avoid the raised turns and engine loading!

Working interval of temperatures

At a normal mode of movement of the marksman of the index of temperature should fluctuate within an average part of a scale!

At considerable loading of the engine and a heat of external air of the marksman can depart and further to the right on a scale. It should not become an occasion to alarm, the alarm lamp of system of cooling does not blink yet.

Alarm lamp

The blinking of an alarm lamp of temperature / level of a cooling liquid during movement testifies to falling of its level or an overheat

Stop, muffle the engine and establish the reason of malfunctions.

5 stock of fuel

The index works at the included ignition.

Capacity of a fuel tank of front-wheel cars makes 55 litres, and all-wheel drive 62 litres.
If the arrow has reached a reserve field, in a stock remains about 7 litres of fuel.

Fire of a symbol of a gaz station on a control panel reminds, besides, of necessity of refuelling.
Never develop fuel from a tank up to the end.


ATTENTION

For reception of authentic indication of presence of fuel include ignition during refuelling.


6 display

– Indications of periodicity of maintenance service;
– Alarm symbols;
– External temperature;
– Positions of the lever of the selector – address to subsection Automatic transmission;
– Information system водителя*

7 button of dump

– A measuring instrument of run,
– Indications of periodicity of maintenance service

8 speedometer with run counters

Speedometer


The speedometer is equipped by the digital counter of the general run and a measuring instrument of run from the moment of dump.

During the period обкатки and further adhere to Obkatka of instructions resulted in subsection on driving.

Run counters

The bottom counter registers the general run, and top (measuring instrument) – run from the moment of the measurement beginning.

Accuracy of readout of a measuring instrument of run makes 100 m.

The button of dump of a measuring instrument of run


Press the button before installation of zero value of a measuring instrument of run.

Indication of periodicity of maintenance service


On an illustration the display of a control panel with indication of the run which has remained before carrying out of servicing is represented.

Indication of the run which has remained before carrying out of maintenance service

Short-term pressing of the control button (1) at the included ignition on indication deduces quantity of the kilometres which have remained before maintenance service. Check of work of system can be carried out both at muffled, and at the working engine and at speed no more than 5 km/h.

Indication of the quantity which have remained before maintenance service of kilometres is updated each 500 km of run.
On the display of the new car, and also after maintenance service carrying out, throughout the first 500 km of run indication “SERVICE IN 15000 KM” is always deduced.

It concerns also cars with maintenance service “Longlife”.

In the presence of malfunction of 1st degree priority (a red symbol) the call of indication of the quantity which have remained before maintenance service of kilometres is impossible.

At approach / approach of term of passage of the next maintenance service, after ignition inclusion on the display indication “SERVICE IN 2000 KM” or “SERVICE is deduced!”. Later 5 seconds the display are switched to a normal mode of indication.

Sbrasyvanie indications of periodicity of maintenance service

Sbrasyvanie indications it is carried out on spending maintenance service HUNDRED Audi.

Independently to dump indication it is possible as follows:

Switch off ignition.
At the pressed button (2) include ignition. On the display there is an indication “SERVICE!”
ATTENTION

Dump indication in a starting position only according to intervals of carrying out of maintenance service. Otherwise it will not represent the facts.
At an accumulator detachment the given indications of maintenance service remain.


Display of faults

In the presence of malfunction on a place of indications of a measuring instrument of run of a control panel there is an indication “dEF”. Malfunction urgently eliminate on HUNDRED Audi.

Control lamps

The electronic control of capacity двигателя*1) ЕРС

(Electronic Power Control)

The control lamp lights up at ignition inclusion. In the absence of malfunction it should go out after engine start.

1) the Control lamp of system of preheat of the diesel engine

The control lamp lights up at occurrence during malfunction movement in a control system of the engine. The control system of capacity of the engine is automatically switched to the emergency program. Thus capacity of the engine a little decreases. Urgently address on HUNDRED Audi.

Preheat system (only diesel engines)

At inclusion of ignition of the cold engine the control lamp lights up. Lamp fire testifies to inclusion of preheat of the engine.

The lamp dies away after achievement of temperature of ignition. The engine get at once as soon as the lamp will go out – address to subsection the Lock of ignition and engine start.

At start of the heated-up engine, and also at external temperature above +8С the control lamp of system of preheat lights up approximately for one second – the engine can be got at once.

If at the cold engine the control lamp does not light up, malfunction in preheat system can be the reason. In this case address for the qualified help.

At malfunction occurrence in a control system of the engine during movement the control lamp starts to blink. Engine management is switched automatically to the emergency program. Thus its capacity a little decreases.
Urgently address on HUNDRED Audi.

Turn indexes on прицепе*

At movement with the trailer control лампа* blinks synchronously with the included indexes of turn.

At malfunction of a lantern of the index of turn on the car or the trailer the control lamp does not blink.

Parking light / light of headlights

The control lamp burns at included lay fires and headlights.

Antiprobuksovochnaja system (АSR) *1)

The control lamp lights up at inclusion of ignition and should go out approximately in two seconds.

The lamp blinks during movement at work ASR.

At the switched off device or in the presence of malfunction the control lamp burns constantly.

As system ASR works together with ABS at refusal ABS control lamp ASR burns also.

For more detailed data address to subsection Switches and switches.

1) Control lamp ESP on cars with the electronic program of stability.

The electronic program of stability (ESP)

The control lamp lights up at inclusion of ignition and should go out approximately in 2 seconds.

The lamp blinks during movement at work ESP.

At the switched off device or in the presence of malfunction the control lamp burns constantly.

As ESP works together with ABS, at refusal ABS control lamp ESP burns also.


ATTENTION

At fire of a control lamp right after engine start there can be protective switching-off ESP caused by system.
In this case you can include ESP deenergizing and the subsequent inclusion of ignition. The control lamp dies away also the device is completely ready for operation.
For more detailed data address to subsection Switches and switches.


Electronic anticreeping blocking


At ignition inclusion the inquiry of the data of a key of the car is carried out. The positive result of data exchange proves to be true short fire of a control lamp.

At using not coded key (for example, the duplicate) a control lamp begins is long to blink. In this case start of the engine of the car is impossible. Address also to subsection Keys, locks of a body with uniform management
And the security alarm system
.

Headlight


The control lamp lights up at inclusion of a headlight or at using a light signal – address to subsection Switches and switches.

Turn indexes



The control lamp blinks synchronously with the included indexes of turn. At refusal of one of turn indexes the control lamp blinks twice more often. Told does not concern movement with the trailer.

For more detailed data address to subsection Switches and switches.

At the included emergency light alarm system both control lamps of indexes of turn synchronously blink.

Electronics двигателя*


The control lamp signals about malfunction of electronics of the engine. Urgently address on HUNDRED Audi and eliminate a cause of defect.

System of pillows of safety AIRBAG

The control lamp of system of pillows and devices of a pyrotechnic tension of belts should light up after inclusion of ignition and die away in some seconds.

At the disconnected pillow of the forward passenger the control lamp burns in the beginning continuously 4 seconds, then 15 seconds then dies away blink. Thereby the signal about switching-off of a pillow of the forward passenger is given, address also to subsection of System of safety. Transportation of children.

The system is faulty, if a control lamp:

does not light up at inclusion of ignition,
does not die away after inclusion of ignition or
lights up during movement.

About malfunction constant burning of a control lamp signals.
ATTENTION

In case of malfunction of system check up it at the first possibility on HUNDRED Audi. Otherwise there is a danger of that at failure there will be no regular operation of pillows or devices of a pyrotechnic tension of belts.



System of antiblocking of brakes (ABS)


The control lamp watches work ABS.

АBS

Availability for service of basic electric components ABS is checked before the beginning and during movement by the electronic monitoring system.

The control lamp lights up at inclusion of ignition and should go out approximately in 2 seconds.

If control lamp ABS does not die away or lights up on the move the device is faulty. In this case car braking only with use of usual brake system is possible.

If at malfunction ABS the alarm lamp of brake system in addition lights up, consider the following:
ATTENTION

With refusal of regulating function ABS at braking back wheels can be blocked rather quickly. Under certain conditions it can lead to car drift.
In this case cautiously move on the nearest HUNDRED Audi and eliminate malfunction.



At failure ABS of cars with антипробуксовочной system / the electronic program of stabilisation of course stability control lamp ASR / ESP burns also. For more detailed data address to subsections Switches and switches and Features of driving of the car and auxiliary systems (ABS, EDS, ASR, ESP).

Electronic blocking of differential (EDS) *

EDS works together with ABS.

At refusal ABS does not work also EDS.

Manual brake


The control lamp lights up at tightened manual a brake and the included ignition. It should die away after отпускания a manual brake.

The accumulator category


The control lamp lights up at inclusion of ignition and should go out after engine start.

If the lamp does not die away or lights up during car movement as a rule still it is possible to reach to the nearest HUNDRED Audi. As thus, however, there is a continuous category of the accumulator it is necessary to switch off all consumers of a current, except the most necessary.

On cars with information system of the driver there is still an additional lamp of the control of pressure of the accumulator.

Reminder about необходи pave пристегнуться*

The control lamp lights up for some seconds after ignition inclusion, reminding of necessity to fasten seat belts.

Alarm symbols (standard execution)


At inclusion of ignition and during movement of cars without information system of the driver (FIS) mentioned below functions and a technical condition of systems of the car are continuously supervised.

About arising malfunctions, or the system informs on necessity of urgent performance of repair-preventive works as a sound signal, accompanying its red and yellow light symbols on a control panel, depending on degree priority.

If under control functions are perfectly in order, for some seconds letters “ОК” are highlighted.

Symbols of red colour (a priority 1)

Malfunction of brake system
Falling of level of a liquid in system of cooling below norm or its overheat
Pressure drop of oil below norm

At occurrence of a blinking red symbol three precautionary sound signals following one after another are distributed. Symbols signal about danger. Stop, muffle the engine, check up the refused system and eliminate malfunction. The qualified help probably for this purpose is required.

At occurrence at once several refusals of the first degree priority symbols appear consistently, with duration of indication of each of them of 2 seconds. The blinking of symbols proceeds before malfunction elimination.

Yellow symbols (a priority 2)

Reserve stock of fuel
Deterioration brake колодок
Check up level impellent масла*
Malfunction of a sensor control of level of impellent oil

At occurrence of a yellow symbol one warning signal is distributed. Indication of symbols – a prevention signal. As soon as possible check up corresponding functional indication. At simultaneous indication of several preventions symbols appear consistently, within approximately 2 seconds everyone.

The prevention of an open door / a luggage carrier

 

At the included ignition the symbol of the digital display specifies in open doors and a luggage carrier. Irrespective of an open door, the pictogramme always shows an open door of the driver. The luggage carrier represented on the pictogramme blinks at its open door.

After correct closing of all doors and a luggage carrier the given symbol dies away.

Brake system

 

The symbol blinks at too low level of a brake liquid or at malfunction ABS.

In this case stop, and check up level of a brake liquid.

At falling of level of a brake liquid in the refuelling tank below a mark “Min” cautiously reach to the nearest HUNDRED Audi, add a brake liquid and establish the reason of decrease in its level. At refusal ABS there is no regulation of brake effort of the back bridge. Therefore back wheels have the big propensity to blocking.
ATTENTION

Refusal of one of contours of a two-planimetric hydrodrive of brakes can be the reason of falling of level of a brake liquid below norm and increase in a free wheeling of a brake pedal.
In this case though also it is possible to reach with care to the nearest HUNDRED Audi, however on road remember increase in a brake way and effort to a pedal.
At normal level of a brake liquid the reason can consist in malfunction ABS. With failure of regulating function ABS at braking rather fast blocking of back wheels can take place. Under certain circumstances it can lead to drift of the back bridge of the car.
Cautiously reach the nearest HUNDRED Audi, and eliminate malfunction.



Temperature / level of a cooling liquid


 

The symbol blinking on the move testifies to an overheat of a cooling liquid or falling of its level below norm.
Stop, muffle the engine and check up liquid level. If necessary add a liquid.
ATTENTION

Be cautious at opening of a stopper of a broad tank of system of cooling! The system of cooling of the heated-up engine is under pressure – danger of a burn at liquid emission! Therefore, before to turn away a stopper, allow to the engine to cool down.
Do not substitute a hand under the fan!
If level of a cooling liquid in norm refusal of the fan of system of cooling can be the overheat reason.



Do not continue movement if the lamp does not die away – take advantage of the qualified help.

Pressure of impellent oil

 

At a blinking of the given alarm symbol muffle the engine, check up level of oil and if necessary add

At a blinking of a symbol and normal level of oil it is impossible to continue movement. Engine work idling is not supposed – take advantage of the qualified help.
ATTENTION

The alarm symbol of pressure of oil is not the index of its level in greasing system!
Therefore check oil level regularly, is better at refuelling.



Reserve stock of fuel

 

Urgently fill the car.

Deterioration of forward brake overlays

 

Address on HUNDRED Audi for check of overlays brake колодок lobbies and, in addition, back wheels.

Check up level impellent масла*

 

At occurrence of the given symbol as soon as possible check up level of oil and add it

Malfunction of a sensor control impellent масла*

 

Address on HUNDRED Audi for check of the gauge of level of oil.

Indication of external temperature (standard execution)

 

Indication of external temperature appears at the included ignition.

At temperatures from +5С to-5S to the left of temperature indication the snowflake is highlighted.

Occurrence of a symbol in the form of a snowflake warns the driver about necessity of extra care in view of danger of ice.

On the motionless car or at movement with very small speed indication can be a little above actual temperature owing to heat radiated by the engine.

On cars with the conditioner, at display switching on indications under the Fahrenheit scale (F) accordingly indication of external temperature automatically changes

Information system of the driver (FIS) *

The display

 

On the display of information system of the driver (FIS) the following indication can be deduced:

the Prevention of an open door / a luggage carrier
radio frequency Indication
Indication of external temperature
the Monitoring system of malfunctions
the Alarm system of excess of speed
the Travelling computer
Positions of the lever of the selector (automatic transmission) *
the Given systems навигации* (using navigation system is considered in the applied operation manual).
ATTENTION

On cars with automatic transmission indication is deduced on the display only after inclusion of a mode of movement.



 

At consecutive нажимании keys “Reset” (dump) join following modes:

– External temperature / the travelling computer / monitoring systems of malfunctions or
– System indication навигации*
– Display deenergizing

Display of faults of the monitoring system of malfunctions is highlighted also at the switched off display.

Using navigating system Audi probably only at the included display.

The prevention of an open door / багажнике1)

 

At the included ignition the symbol of the digital display specifies in open doors and a luggage carrier. As an example on an illustration the open door of the forward passenger, a back left door and a luggage carrier are shown. The luggage carrier represented on the pictogramme blinks at its open door.

1) On cars with information system of the driver (FIS).

After full closing of all doors and a luggage carrier the given prevention dies away and on indication corresponding functions of information system of the driver will be deduced.

Indication радиосистемы1)

In the absence of display of faults of 2nd degree priority and the included radio (depending on a radio complete set) after will go out letters “ОК”, on the display there is a name of radio station or a radio frequency with the additional information.

The given indication is the additional information of the radio display.

Indication external температуры1)

 

Indication of external temperature appears at the included ignition. On cars with automatic transmission indication appears only after inclusion of a mode of movement.

At temperatures from +5С to-5S to the left of temperature indication the snowflake is highlighted.

1) On cars with information system of the driver (FIS).

Occurrence of a symbol in the form of a snowflake warns the driver about necessity of extra care in view of danger of ice.

On the motionless car or at movement with very small speed indication can be a little above actual temperature owing to heat radiated by the engine.

On cars with the conditioner, at display switching on indications under the Fahrenheit scale (F) accordingly indication of external temperature automatically changes

The monitoring system of malfunctions автомобиля1)

At the included ignition and during movement the system of the automatic control of malfunctions continuously supervises certain functions and a technical condition of systems of the car.

About arising malfunctions, or the system informs on necessity of urgent performance of repair-preventive works as a sound signal, accompanying its red and yellow light symbols on a control panel, depending on a priority. Besides, as the help to the driver, along with some red symbols, on the display there can be an indication of instructions to the driver.

Indication of following preventions and signals about refusals is possible:

1) On cars with information system of the driver (FIS).

Symbols of red colour (a priority 1)

 


Malfunction of brake system
Falling of level of a liquid in system of cooling below norm or its overheat
Pressure drop of oil below norm

At occurrence of a blinking red symbol three precautionary sound signals following one after another are distributed. Symbols signal about danger. Stop, muffle the engine, check up the refused system and eliminate malfunction. Probably, the qualified help for this purpose is required.

 

At occurrence at once several refusals of 1st degree priority symbols appear consistently, with duration of indication of each of them of 2 seconds. The blinking of symbols proceeds before malfunction elimination.
ATTENTION

In case of malfunction occurrence at the included system of navigation *, for some seconds on a place of indication of system of navigation there is an alarm symbol of 1st degree. Then the given symbol moves upwards in the field of indication of 2nd degree priority, and on its place again there is an indication of system of navigation.
In the presence of malfunction of 1st degree priority indication of 2nd degree priority is not deduced.



Yellow symbols (a priority 2)

Malfunction of a signal торможения2)

BREMSLICHT
Peregoranie lamps of a passing light or backing
Falling below norm of level of a washing liquid
Reserve stock of fuel
Deviation of pressure of the accumulator from norm
Check up level impellent масла*
Malfunction of a sensor control of level impellent масла*
The alarm system of excess of speed
Malfunction of dynamic regulation of an angle of slope фар*

2) Depending on the country – a symbol or an inscription.

At occurrence of a yellow symbol one warning signal is distributed. Indication of symbols – a prevention signal. As soon as possible check up corresponding functional indication. At simultaneous indication of several preventions symbols appear consistently, within approximately 2 seconds everyone.

The control button

 

The control button has following appointment:

The control of indication of symbols.

Short-term pressing of the control button, at the included ignition, makes a consecutive call on indication of all symbols. Check of work of system can be carried out both at muffled, and at the working engine and at speed no more than 5 km/h.

In the presence of malfunction of 1st degree priority (a red symbol) the indication control is impossible.

Conclusion to indication of instructions to the driver

At a blinking of any symbol of 1st degree priority, as the help to the driver on the display corresponding instructions can be deduced.

For example: “MOTOR ABSTELLEN, OLSTAND PRUFEN” (muffle the engine, check up oil level).
For выcandlesивания press the control button. Indication dies away approximately in 5 seconds after отпускания buttons.

Illumination of the counter of the passed way

At the switched off ignition press the control button – approximately within 15 seconds indication of the counter of the passed way is highlighted.

Check of work of system

 

After inclusion of ignition the monitoring system of malfunctions of the car carries out the automatic control of functions.

Cars with a manual box of a gear change – РКПП

If checked up by the monitoring system of malfunctions of function is perfectly in order, for some seconds indication “ОК” lights up.

In the presence of malfunctions, after ignition inclusion there is their indication (instead of indication “ОК”). The acoustic warning signal (is simultaneously distributed at simultaneous occurrence of malfunctions of 1 and 2 degrees priority three warning signals).

At absence on the display of indication of malfunction, and also letters “ОК” the system is subject to check.

Cars with automatic transmission

After ignition inclusion (the selector lever in position “Р” and “N”) on the display appears the instruction to the driver: “BEIM EINLEGEN EINER FAHRSTUFE IM STAND FUSSBREMSE BETATIGEN” (at inclusion of a mode of movement of the motionless car press a brake pedal).

At a choice a movement mode (“R”, “D” etc. the instruction to the driver dies away, and after pressing of a pedal of a brake the automatic control of functions is carried out.

If under control functions are perfectly in order, for some seconds letters “ОК” are highlighted.
In the presence of one or several malfunctions, approximately in 15 seconds after engine start, the instruction to the driver is replaced by indication of corresponding symbols of malfunctions.

Display of faults

At infringement of malfunctions of functions under control to the monitoring system the acoustic warning signal is distributed. Simultaneously occurrence of following symbols is possible:

Brake system

 

The control lamp blinks at falling of level of a brake liquid below norm or at malfunction ABS.
Stop and check up level of a brake liquid.
At falling of level of a brake liquid below a mark “Min” it is possible to reach with care to the nearest HUNDRED Audi on purpose доливания liquids and findings-out of the reasons of its leak. At refusal ABS there is no regulation of brake effort of the back bridge. Therefore back wheels have the big propensity to blocking.
ATTENTION

The reason of falling of level of a liquid in the tank below norm and simultaneous increase in a free wheeling of a brake pedal refusal of one of contours of a two-planimetric hydrodrive of brakes can be.
In this case though also it is possible to reach with care to the nearest HUNDRED Audi, however on road remember increase in a brake way and effort to a pedal.
At normal level of a brake liquid the reason can consist in malfunction ABS. With failure of regulating function ABS at braking rather fast blocking of back wheels can take place. Under certain circumstances it can lead to drift of the back bridge of the car.


Cautiously reach the nearest HUNDRED Audi, and eliminate malfunction.

Temperature / level of a cooling liquid

 

The overheat or falling of level of a cooling liquid can be the reason of a blinking of a lamp during movement.
Stop, muffle the engine, check up level of a cooling liquid and if necessary add it.
ATTENTION

Be cautious, opening a stopper of a broad tank of system of cooling! The system of cooling of the heated-up engine is under pressure – danger of a burn at liquid emission! Therefore, before to turn away a stopper, allow to the engine to cool down.



Do not substitute a hand under the fan!

If level of a cooling liquid in norm refusal of the fan of system of cooling can be the overheat reason.

If the control lamp does not die away, it is impossible to continue movement. Take advantage of the qualified help.

Pressure of impellent oil

 

At a blinking of the given symbol stop, muffle the engine, check up level of oil and if necessary add it

It is impossible to continue movement if the symbol blinks at normal level of oil. Do not suppose engine work idling – take advantage of the qualified help.
ATTENTION

The control lamp of pressure of oil is not the index of its level in greasing system!
Therefore check oil level regularly, is better at each refuelling.



BREMSLICHT or


At fire of an inscription or a symbol to check and if necessary replacement, or to repair on HUNDRED Audi are subject:

– Lamps of stoplights,
– Safety locks,
– Connections in electroconducting,
– The switch of a signal of braking (only at censures during the function control).

Peregoranie lamps of a passing light or lamp of a lantern of a backing

 

Malfunction can be caused following reasons:

– Have fused lamps
– Safety locks and
– Connections in electroconducting are broken.

Replace independently or with HUNDRED Audi faulty lamps / safety locks.

The function control “blowing lamps of a passing light or a lamp of a lantern of a backing“ is carried out only at included light.

Washing liquid

 

Add washing liquid in the tank glass - and фароомывателя*

Fuel reserve

 

Urgently fill the car.

Deviation of pressure of the accumulator from norm

 

Address on HUNDRED Audi and check up a tension клинового a belt, a regulator / an accumulator condition.

Control lamp of the category of the accumulator

Check up level impellent масла*

 

At occurrence of the given symbol as soon as possible check up level of oil and add it

Malfunction of a sensor control of level impellent масла*

 

Address on HUNDRED Audi for check of the gauge of level of oil.

Malfunction of dynamic regulation of an angle of slope фар*

 

Address on HUNDRED Audi for repair of a regulator of an angle of slope of headlights.

The excess alarm system скорости1)

 

The alarm system of excess of speed allows to establish its limit at which excess approximately on 10 km/h, the warning signal is distributed. Simultaneously on the display there is an alarm symbol “km/h”.
ATTENTION

Irrespective of presence of the device of the alarm system of excess of speed, supervise admissible ПДД the maximum speed on a speedometer.



1) On cars with information system of the driver (FIS).

Process of programming of speed of degrees of the prevention 1 and 2 and their cancellations is more low described.

Degree of the prevention 1

 

The alarm symbol dies away at reduction of speed below the programmed threshold. The symbol dies away besides at increase of speed approximately on 40 km/h above the programmed threshold during a minimum of 10 seconds. Thus however there is no dump of the data of memory of the programmed restriction of speed.

Programming of speed

At the moment of indication on a speedometer of the necessary speed press and release the control button of the monitoring system of malfunctions. Input in memory proves to be true выcandlesиванием an alarm symbol of restriction of speed at release buttons.

The programmed value of speed remains in memory before following pressing of the button at other speed or dump of the data of a memory.

Cancellation of the entered restriction of speed

 

At speed more than 5 km/h press the control button more than one second. Restriction cancellation proves to be true the crossed out alarm symbol.

At ignition deenergizing there is an automatic dump of the data of memory of a memory.

Degree of the prevention 2

 

At the switched off ignition the driver can program a continuous threshold of the prevention.

Prevention indication is highlighted on the display. The alarm symbol dies away unlike prevention degree only at decrease in speed below the programmed size.

Programming of the given prevention is recommended in need of a reminder to the driver of maintenance of certain speed as addition to degree of the prevention 1. (For example, at movement in the country with restriction of speed, the maximum speed at movement with winter tyres etc.).

Programming of speed

At the switched off ignition press and release the control button. Indication of the counter of the passed way is highlighted.

Again press a minimum for 2 seconds the control button. On the display there is a size of an actual threshold of restriction of speed.

 

For change of speed press the top or bottom party of the switch of functions (marksman) of the travelling computer. Thus occurs stage-by-stage (one stage of 10 km/h) increase or reduction of values.

In some seconds after end of programming display illumination is again switched off.

The programmed value of speed remains in memory before following pressing of the button at other speed or dump of the data of a memory.

Cancellation of the entered restriction of speed

At the switched off ignition press and release the control button. Display illumination joins. Again press approximately for 2 seconds the control button – there is an indication of the established speed. In end press and keep a key “Reset” the travelling computer before occurrence of the crossed out alarm symbol.
On the main page