Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
- The power supply system and release
   + The power supply system - petrol models
   - The power supply system - diesel models
      Filling of the power supply system with fuel and removal from it air stoppers
      Check and adjustment of the maximum turns of the engine
      Removal, installation and adjustment of the thermosensitive gauge of turns of fast idling
      Electromagnetic запорный the valve - the general data, removal and installation
      Removal and installation ТНВД
      Methods of check of installation of the moments of injection of fuel
      Check and adjustment of the moments of injection (ТНВД Lucas)
      Check and adjustment of the moments of injection (ТНВД Bosch)
      Check of serviceability of functioning, removal and installation of atomizers of injection of fuel
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Removal and assemblage installation топливозаборника with the gauge of the expense of fuel
      Removal and installation of a fuel tank
      Removal and installation of the inlet pipeline and final collector
      turbocharger - the general data and safety measures
      Removal and installation турбокомпрессора
      Check of a condition and regenerative repair турбокомпрессора
      Removal and installation of the built in cooler турбокомпрессора
      Removal and installation of an air cleaner and accompanying components
   + Systems of decrease in toxicity and release of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal, installation and adjustment of the thermosensitive gauge of turns of fast idling

Removal

At assemblage the new sealing washer is required.

The gauge is located in a wall of a casing of the thermostat/assemblage of the fuel filter.

 PERFORMANCE ORDER

1. For the purpose of providing of access, remove a casing воздухораспределителя. In case of need remove also an inlet air line and disconnect a ventilating hose from a jellied mouth of impellent oil. More in detail sm corresponding sections of the present Chapter.
2. Empty cooling system (address to the Head Routine maintenance).

3. Loosen the tightening the screw/nut also disconnect a tip drive a cable of fast idling from the cable core on the lever of fast idling ТНВД.



4. Extend a cable from the adjusting screw located on arm ТНВД.

5. By means of approaching рожкового a key turn out the thermosensitive gauge from a casing of the thermostat/assemblage of the fuel filter. Remove the gauge together with a cable. At a corresponding complete set remove a sealing washer.

Installation

 PERFORMANCE ORDER

1. If the gauge has been established on hermetic, carefully remove from assemblage all traces of the last. Track, that hermetic did not remain hammered in internal охладительные casing channels.
2. Establish the gauge on the regular place, having taken advantage of fresh hermetic, or having replaced a sealing washer.
3. Fill the adjusting screw in an arm on ТНВД and by hand screw a counternut.
4. Fill the cable core in the lever of fast idling, put on a cable a tip (do not tighten while tightening the screw/nut).
5. Make cable adjustment (see more low).

Adjustment

 PERFORMANCE ORDER

1. At the cold engine wring out the lever of fast idling towards a flywheel arrangement. Having pressed a cable tip to the lever, tighten a tightening nut/screw.
2. Adjust the screw so that the lever nestled on an emphasis, then tighten a counternut.
3. Measure length of an open site of the core of a cable.
4. Where it is required, establish into place a casing воздухораспределителя and connect a ventilating branch pipe to a jellied mouth of impellent oil.
5. Fill cooling system (address to the Head Routine maintenance), then start the engine and warm up it to normal working temperature.
6. Make sure available a weak point drive a cable of fast idling. Absence of a weak point with the big degree of probability testifies to malfunction of the thermosensitive gauge.
7. At the hot engine and the serviceable gauge the cable should have a free wheeling in size about 6 mm.
8. Make sure that engine turns raise at отжимании the lever of fast idling towards a flywheel. At the lever pressed to an emphasis turns of fast idling should correspond requirements of Specifications. More detailed information on exact check of turns of the engine is resulted in the Head Routine maintenance.
9. Muffle the engine.



On the main page