Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   + 4.1. Engine OHV (with a camshaft in the block of cylinders)
   + 4.2. Engines OHC
   - 4.3. Engine DOHC with 16 valves
      4.3.1. A technical characteristics
      4.3.2. Compression check
      + 4.3.3. The operations demanding removal of the engine
      4.3.4. Removal of auxiliary components of the engine
      4.3.5. Removal and installation of the valve of adjustment of pressure of oil
      + 4.3.6. A gear belt
      4.3.7. Removal and installation of the mechanism of a tension of a gear belt and rollers
      4.3.8. Removal, check and installation of camshafts
      + 4.3.9. A head of the block of cylinders
      4.3.10. Removal and installation of the oil pallet and маслоотражательной plates
      - 4.3.11. The oil pump
         4.3.11.1. Removal and installation
         4.3.11.2. Repair of the oil pump
      4.3.12. Removal and installation of the valve of the thermostat of an oil radiator
      + 4.3.13. Pistons and rods
      4.3.14. Removal and flywheel installation
      + 4.3.15. Replacement of sealing rings
      4.3.16. Removal, check and installation of bearings of a cranked shaft
      4.3.17. Check of components of the engine
      4.3.18. Removal and engine installation
      4.3.19. Start of the engine after major repairs
   + 4.4. Diesel engines 16D and 16DА
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

4.3.11. The oil pump

4.3.11.1. Removal and installation Removal

PERFORMANCE ORDER
1. Remove a gear belt.
2. Disconnect pipelines of an oil radiator from a casing of the filter and move them aside.
3. Uncover heads of the block of cylinders and pulleys of camshafts.
4. Remove the mechanism of a tension of a gear belt and directing rollers.
5. Unscrew a bolt of fastening of a pulley of a cranked shaft. For keeping of a cranked shaft from проворачивания include any transfer and press a brake.
6. Using a stripper, remove a pulley of a cranked shaft. Remove a lining located behind a pulley, and a back casing of a gear belt.
7. Remove the oil pallet, маслозаборную a pipe and маслоотражающую a plate.
8. Unscrew bolts and remove the oil pump from the block of cylinders. Clear interfaced surfaces of the oil pump and the block of cylinders.

Installation

PERFORMANCE ORDER
1. Apply a thin film greasings on a lining and establish it on the oil pump. Grease working edges of a sealing ring with pure engine oil and, being careful, establish the oil pump on the block of cylinders of the engine.
2. Screw in bolts of fastening of the oil pump, then move the oil pump so that the bottom surface of the pump was flush with the bottom surface of the block of cylinders, and tighten bolts of fastening of the oil pump the demanded moment.
3. Apply a thin film hermetic GM 15 04 200/8 983 368 on an external surface of a lining and move a lining to a cranked shaft.
4. The further installation is made in sequence, return to removal. Remember that at installation it is necessary to use a new gear belt.


On the main page