Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
- Coupling
   Specifications
   + Flywheel and coupling
   - Приводные and карданный shaft, back differential
      Drive of forward wheels - the general information
      Removal and installation of rotary fists, service ступичных assemblages of forward wheels
      Removal, service and installation of a forward power shaft
      Drive of back wheels - the general information
      Removal and installation ступичных assemblages of back wheels, replacement back ступичного the bearing
      Removal, check of a condition and installation of components карданного a shaft
      Check of a condition and replacement of a forward epiploon of back differential
      Removal, service, installation and adjustment of back differential of T-type
      Removal, service, installation and adjustment of back differential of VA-type
      Removal, installation and check of a condition of a forward beam of fastening of back differential
      Removal, service and installation of a back power shaft
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal, check of a condition and installation of components карданного a shaft

Installation details карданного a shaft

1 — Kardannyj a shaft
2 — Back differential
3 — the Plug

Efforts of a tightening of carving connections, Nanometer

Т1: 31
Т2: 52

REMOVAL

 PERFORMANCE ORDER

 Before removal карданного a shaft wind metal parts with rags or a rubber material since at removal these parts can damage rubber protective casings.

1. Disconnect a negative wire from the battery.
2. Establish selector AT lever in position źN╗ / include neutral transfer (РКПП)
3. Release a lay brake.
4. Поддомкратьте the car also establish it on props.
5. Remove central back (with the muffler) sections of system of release of the fulfilled gases, also uncover a thermofilter (see the Head of the Power supply system and release)

6. Mark position карданного a shaft concerning connecting back differential, then release four fixing bolts and turn out three of them.

7. Turn out two bolts of fastening of the central bearing to the car bottom.

8. Liberate карданный a shaft from transmission, - try not to damage epiploons and a rubbing surface of a sliding collar.

 Prepare drain capacity for gathering of oil which will flow out at removal карданного a shaft; right after shaft extraction muffle an aperture in the case of lengthening of transmission by a special cover, or a polyethylene film.

CHECK

 PERFORMANCE ORDER

 The kardannyj shaft is not subject to dismantling.


1. The basic control geometrical parametres карданного a shaft are presented on an illustration.
2. Examine a surface of pipes карданного a shaft on presence of jags or cracks.
3. Estimate deterioration degree шлицевых joints.
4. Check up smoothness and noiselessness of work of hinges.
5. Estimate size люфта, smoothness of a course and noiselessness of rotation of the central bearing.
6. Check up a condition of epiploons.
7. With the help циферблатного a measuring instrument define size of palpation of forward and back sections of a shaft in the central part of pipes. If the result of measurement exceeds 0.6 mm, replace a defective component.

INSTALLATION

 PERFORMANCE ORDER

1. Installation is made in an order, the return to an order of dismantle of components. Track that all fixture has been tightened with demanded effort.
2. Manually turning a shaft, check up it on presence excessive люфта gearings шлицевых connections, also estimate sizes люфтов in крестовинах and bearings карданных hinges.
3. Rotating a hand back wheels, define size of axial palpation карданного a shaft.

 Make measurements in the centre of forward and back pipes карданного a shaft.

4. Pull a shaft every which way around installation of the central bearing for the purpose of definition люфта the last.

On the main page