Subaru Legacy/Outback

1. Check up serviceability of a condition of the cylinder of a door-lock.
2. Make sure that there was no detachment or jamming приводной draughts of the activator.

1. Check up serviceability of a condition of a corresponding safety lock (see more low).
2. Check up serviceability of a condition of contours of giving of a food and grounding of the module of management of the uniform lock (see more low).
3. Check up serviceability of a condition of contours of switches of door-locks (see more low)
4. Check up serviceability of a condition of activators of door-locks (see more low).

1. Check up serviceability of a condition of a contour of the switch (see more low)
2. Make sure of reliability of connection приводной draughts of the activator of the lock of a corresponding door.

1. Check up serviceability of a condition of a contour of the activator (see more low)
2. Make sure of reliability of connection приводной draughts of the activator.

1. Check up a condition of an element of a food of the transmitter (see more low).
2. Check up serviceability of a condition of a safety lock (see more low).
3. Check up serviceability of a condition of contours of giving of a food and grounding of the module of management of remote control (see more low).
4. Replace the management module (see Has undressed Removal, check of a condition and installation of components of the uniform lock).

1. Check up a condition of an element of a food of the transmitter (see more low).
2. Check up serviceability of a condition of a contour of a registration socket (see more low).

1. Check up a condition of an element of a food of the transmitter (see more low).
2. Check up serviceability of a condition of the alarm switch of a key (see more low).
3. Check up a condition of the door switch (see more low).
4. Replace the management module (see Has undressed Removal, check of a condition and installation of components of the uniform lock).

1. Check up a condition of an element of a food of the transmitter (see more low).
2. Check up serviceability of a condition of the alarm switch of a key (see more low).
3. Check up serviceability of functioning of the alarm system (see more low).
4. Replace the management module (see Has undressed Removal, check of a condition and installation of components of the uniform lock).

1. Check up a condition of an element of a food of the transmitter (see more low).
2. Check up serviceability of a condition of the alarm switch of a key (see more low).
3. Check up serviceability of a condition corresponding салонных fixtures (see Has undressed Removal and installation of lighting devices, replacement of lamps).
4. Check up a condition of the door switch (see more low).
5. Replace the management module (see Has undressed Removal, check of a condition and installation of components of the uniform lock).

1. Disconnect electroconducting from the management module (see Has undressed Removal, check of a condition and installation of components of the uniform lock).
2. Measure pressure between plugs №№ 5 (+) and 16 (+) socket В176 of a plait of electroconducting and weight of the chassis. If result of measurement structure ляет more than 10 In, pass to a following stage of check, otherwise check up on presence of breakages and short circuit electroconducting on a chain site between the module of management and a safety lock.
3. Measure resistance between plugs №№ 6 (+) and 14 (+) socket В176 and weight of the chassis. If the result of measurement makes less than 10 Ohm, chains of giving of a food and grounding are perfectly in order, otherwise repair electroconducting.

1. Disconnect electroconducting from the module of management of system of the uniform lock (see Has undressed Removal, check of a condition and installation of components of the uniform lock).
2. Measure resistance between the plug № 7 (+) socket В176 and weight of the chassis in position "is unblocked" of the switch. If the result of measurement makes more than 10 Ohm, the following stage of check can be lowered.
3. Repeat the previous check in position "is blocked" of the switch. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise the switch in norm.
4. Disunite a contact socket of electroconducting of the switch/activator of a door-lock (see Has undressed Removal, check of a condition and installation of components of the uniform lock) and measure resistance between plugs № 1 and № 3 in position "is unblocked" of the switch. If the result of measurement makes less than 10 Ohm, pass to the check final stage, otherwise replace switch/activator assemblage (see Has undressed Removal, check of a condition and installation of components of the uniform lock).
5. Repeat the previous check in position "is blocked" of the switch. If the result of measurement makes less than 10 МОм, replace switch/activator assemblage (see Has undressed Removal, check of a condition and installation of components of the uniform lock), otherwise check up on presence of signs of breakage and short circuit electroconducting on a chain site between the module of management and the corresponding switch.

1. Measure pressure between plugs №№ 17 (+) and 18 (+) socket В176 and weight of the chassis. If the result of measurement makes more than 10 In, pass to a following stage of check, otherwise replace the module of management of the uniform lock.
2. Check up a condition of the corresponding activator (see Has undressed Removal, check of a condition and installation of components of the uniform lock), in case of need make its replacement. If the activator is perfectly in order, check up on presence of signs of breakage and short circuit electroconducting on a chain site between the module of management and the activator. Make necessary regenerative repair.

Take from the transmitter of an element of a food and check up its pressure (see Has undressed Removal, check of a condition and installation of components of the uniform lock). If the result of measurement makes more than 2 In, the transmitter as it should be and should be passed to the next check (see above a card of refusals).

1. Include ignition and disunite a registration socket (see Has undressed Removal, check of a condition and installation of components of the uniform lock). Measure pressure between the plug № 2 (+) socket В176 and weight of the chassis. If the result of measurement makes more than 10 In, pass to a following stage of check, otherwise repair electroconducting / a contact socket.
2. Repeat the above described check at the connected registration socket. If the result of measurement makes 0 In, the registration socket is perfectly in order, otherwise repair electroconducting / a contact socket.

1. Measure pressure between plugs №№ 3 (+) and 4 (+) socket В176 and weight of the chassis. If in public the result of measurement differs from value 0 In, the following stage of check can be lowered.
2. Close all doors and repeat the previous check If in public the result of measurement makes nearby 10 In, hence, switch as it should be, otherwise pass to a following stage of check.
3. Disconnect from the door switch electroconducting and measure resistance between plugs № 1 and № 3 (lateral doors) / № 2 (a back door) the switch. If at wrung out to the pressed button of the switch the result of measurement makes more than 10 МОм, pass to the check final stage, otherwise replace the switch.
4. Repeat the above described check at the released switch. If the result of measurement makes less than 1 Ohm, check up on presence of signs of breakage and short circuit electroconducting on a chain site between the module of management and the switch, otherwise replace the switch.

1. Take from the main assembly block a safety lock № 6 (15) and visually estimate its condition. Fused safety lock replace. If a safety lock in norm, pass to a following stage of check.
2. Take a key from the lock of ignition and measure pressure between the plug № 1 (+) socket В176 and weight of the chassis. If the result of measurement makes 0 In, hence, alarm switch in norm, otherwise pass to a following stage of check.
3. Disconnect from the alarm switch electroconducting. Insert a key into the ignition lock (in position LOCK) and measure resistance between plugs № 1 and № 2 switches. If the result of measurement makes less than 1 Ohm, pass to the check final stage, otherwise replace the alarm switch.
4. Take a key from the lock of ignition and repeat the previous check. If the result of measurement makes less than 1 МОм, replace the alarm switch, otherwise check up on presence of signs of breakage and short circuit electroconducting on chain sites between the switch and a safety lock and between the switch and the management module.

1. Make sure of serviceability of activation of lamps of the alarm system from the corresponding switch on the panel of devices of the car. If lamps blink regularly, pass to a following stage of check, otherwise check up a condition of corresponding electroconducting, make necessary corrections.
2. Take a key from the ignition lock, close all doors (including a back door) and measure pressure between plugs №№ 12 both 13 sockets В176 and weight of the chassis. If the result of measurement makes less than 10 In, replace the module of management of the uniform lock (see Has undressed Removal, check of a condition and installation of components of the uniform lock), otherwise check up on presence of signs of breakage and short circuit electroconducting on a chain site between the module of management and alarm system lamps.

1. Make sure of serviceability of activation of fixtures from the corresponding switch. If fixtures function regularly, pass to a following stage of check, otherwise check up a condition of corresponding electroconducting, make necessary corrections.
2. Disconnect electroconducting from the module of management of the uniform lock and салонного the fixture. Measure resistance between the plug № 11 sockets В176 and the plug № 2 sockets R52. If the result of measurement makes less than 10 In, hence, chain of the fixture is serviceable, otherwise check up on presence of signs of breakage and short circuit electroconducting on a chain site between the module of management and the fixture.

1. Disunite a contact socket of electroconducting of a chain of illumination of the switch of ignition and measure pressure between the plug № 2 (+) socket В224 and weight of the chassis. If the result of measurement makes more than 10 In, pass to a following stage of check, otherwise check up on presence of signs of breakage and short circuit electroconducting on a chain site between the switch of ignition and a safety lock.
2. Disconnect electroconducting from the module of management of the uniform lock. Measure resistance between the plug № 11 sockets В176 and the plug № 1 socket В224. If the result of measurement makes less than 10 In, check up serviceability of a condition of the block of illumination (in case of need make replacement), otherwise repair electroconducting.