Subaru Legacy/Outback

1999-2003 of release

Repair and car operation

Diagnostics of malfunctions SRS

System of self-diagnostics SRS

Check of serviceability of functioning of control lamp SRS/AIR BAG

Include ignition, - control lamp SRS should light up and remain with burning a condition within nearby 6 seconds. Refusal of a lamp of deenergizing testifies that the block of self-diagnostics SRS has revealed the malfunction which code is brought in memory of the processor (see more low).

Reading of codes of malfunctions SRS

Include ignition (the engine do not start).

Reading written down in memory of the module of self-diagnostics of codes is made by calculation of gleams of control lamp SRS/AIR BAG. The long gleam (1.2) corresponds decimal (10), short (0.3), - to individual categories of numerical value DTC. So, the code 12 will look as follows: one long gleam + two short.

Codes are highlighted three times with intervals in 1.2 with. Write down считанную sequence, then switch off ignition, disconnect the diagnostic plug, analyse codes (see more low) and make necessary regenerative repair.

The conclusion of a code testifies to a system working order in the form of uniform gleams duration 0.6 with with an interval also 0.6 with.

Switch off ignition, disconnect the diagnostic plug, wind with its adhesive tape and return in a starting position.

Clearing of memory of the block of self-diagnostics

Having finished works on correction of the revealed malfunctions, repeat procedure of reading of codes of malfunctions.

Make sure that ignition is included and connect the diagnostic plug to the plug № 2 diagnostic sockets.

In a course выcandlesивания codes a control lamp a minimum for 3 seconds connect the second diagnostic plug to the plug № 3 diagnostic sockets. As soon as memory of the module of management will be cleared, the control lamp will start to highlight a code of a working order of system. Refusal of a lamp of transition in a mode of a uniform blinking testifies to preservation in memory of the module of management of codes of refusals, - execute corresponding corrections, then repeat procedure of clearing of memory.

Having finished clearing of memory of the module of management, disconnect diagnostic plugs, wind with their adhesive tape and return in starting positions.

Problem diagnostics SRS

Refusals of control lamp SRS/AIR BAG

Control lamp ABS is not activated at ignition inclusion

Try to include ignition, without making engine start, - if other, a part combinations of devices, control lamps work regularly, pass to a following stage of check, otherwise it is necessary to make the necessary regenerative device of an instrument guard.

Take a safety lock 5 in the main assembly block of safety locks and check up its condition. Replace fused safety lock. If the safety lock is serviceable, pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then disunite contact pair АВ1/В31. Connect a negative wire to the battery and include ignition if the control lamp lights up, pass to a following stage of check, otherwise replace a lamp, or the printed-circuit board of a combination of devices (see Has undressed Removal, service and installation of a combination of devices, check of a condition of components).

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then connect sockets АВ1 and В31 and disunite socket АВ6 of the module of management SRS. Connect a negative wire to the battery and include ignition, - if the control lamp lights up, replace the management module, otherwise replace the main plait of electroconducting SRS.

Control lamp ABS is not disconnected after realisation of start of the engine

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then remove an overlay of a threshold of a driver's door (the Body see the Head) and check up reliability of contact connection of sockets АВ1/В31. In case of need make necessary regenerative repair, or replace the main plait of electroconducting SRS. If sockets are perfectly in order, pass to a following stage of check.

Not including ignition, connect a socket 1А a diagnostic plait of Ak to socket В31 кузовной electroconductings. Connect a negative wire to the battery and include ignition. Connect sockets 3А and 4А a diagnostic plait And if control lamp SRS goes out, the following stage of check can be passed.

Check up a plait condition кузовной electroconductings, make corresponding regenerative repair. If electroconducting is perfectly in order, replace the printed-circuit board of a combination of devices (see Has undressed Removal, service and installation of a combination of devices, check of a condition of components).

Estimate reliability of contact between the module of a pillow of safety and socket АВ6. In case of need make corresponding regenerative repair of the main plait of electroconducting SRS. If no infringements are revealed, pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then connect sockets АВ1 and В31 and disunite contact pair АВ3/АВ8. Take two clamps, lower a ware box and disunite contact pair АВ9/АВ10 (see in the same place). Disconnect socket АВ6 from the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Connect a negative wire to the battery, include ignition and connect among themselves sockets 4I and 5I a diagnostic plait if control lamp SRS goes out, pass to a following stage of check, otherwise make necessary regenerative repair of the main plait of electroconducting SRS.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then connect contact pair АВ1/В31, connect to socket В31 socket А1 of a diagnostic plait And and measure resistance between plugs №№ 17 and 18 sockets 5А a plait And and weight of the chassis. If the result of measurement makes more than 10 Ohm, restore quality of grounding of a body on weight, otherwise pass to the check final stage.

Restore connection of contact pair АВ1/В31, disconnect socket АВ6 from the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Measure resistance between plugs №№ 9 and 10 sockets 2I a diagnostic plait and weight of the chassis. If the result of measurement makes less than 10 Ohm, replace the management module, otherwise replace the main plait of electroconducting SRS.

Refusals of working components SRS

Diagnostic code 11

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect a diagnostic plait from socket АВ7, then remove the bottom section of furnish of the panel of devices, disunite contact pair АВ3/АВ8 and connect a socket 1F plait F to socket АВ8. To a socket 3F connect feigning resistor SRS. Connect a negative wire to the battery and include ignition, - at serviceable functioning of a control lamp replace a contact drum, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS see) - the device and a functioning principle), disconnect feigning resistor from a socket 3F diagnostic plait F, remove a ware box (the Body see the Head) and disunite contact pair АВ10/АВ9 of the module of a passenger pillow of safety. Disunite socket АВ6 of the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Measure resistance between plugs № 1/4 sockets 2I a plait I and plugs № 4/3 accordingly a socket 3F plait F. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise make replacement of the main plait of electroconducting SRS.

Measure resistance between plugs №№ 4 sockets 2I and 3F. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Diagnostic code 12

Disconnect SRS (the Section System of additional safety (SRS see) - the device and a functioning principle), take two clamps and remove a ware box (the Body see the Head). Disunite contact pair of the module of a passenger face-to-face pillow of safety АВ9/АВ10 and connect a socket 1F diagnostic plait F to socket АВ9. Connect feigning resistor SRS to a socket 3F plait F, then connect a negative wire to the battery and include ignition, - at serviceable functioning of control lamp SRS replace the module of a passenger pillow of safety, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS see) - the device and a functioning principle), disconnect feigning resistor from a socket 3F, remove the bottom section of furnish of the panel of devices and disunite contact pair АВ3/АВ8 of electroconducting of a cable drum of a steering column. Disunite socket АВ6 of the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Measure resistance between plugs № 2/5 sockets 2I a plait I and plugs № 4/3 accordingly a socket 3F plait F. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise make replacement of the main plait of electroconducting SRS.

Measure resistance between weight and plugs № 2 and № 5 sockets 2I, and also between both given plugs and weight of the chassis. If the result of measurement makes more than 1 МОм, replace the module of management SRS, otherwise replace the main plait of electroconducting.

Diagnostic code 15

Disconnect SRS (the Section System of additional safety (SRS see) - the device and a functioning principle), disconnect feigning resistor from a socket 3F diagnostic plait F, remove a ware box (the Body see the Head) and disunite contact pair АВ10/АВ9 of the module of a passenger pillow of safety. Disunite socket АВ6 of the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Measure pressure between plugs №№ 4 and 1 socket 2I plait I/I2 and weight of the chassis. If the result of measurement makes less than 1 In, the module of management SRS, otherwise replace the main plait of electroconducting SRS.

Diagnostic code 16

Disconnect SRS (the Section System of additional safety (SRS see) - the device and a functioning principle), disconnect feigning resistor from a socket 3F, remove the bottom section of furnish of the panel of devices and disunite contact pair АВ3/АВ8 of electroconducting of a cable drum of a steering column. Disunite socket АВ6 of the module of management SRS and connect a socket 1I a diagnostic plait I or I2. Measure pressure between plugs №№ 2 and 5 sockets 2I plait I/I2 and weight of the chassis, - if the result of measurement makes less than 1 In, replace the module of management SRS, otherwise replace the main plait of electroconducting SRS.

Diagnostic code 21

Presence at memory of the module of self-diagnostics of a code 21 testifies to necessity of performance of replacement of the module of management SRS.

Diagnostic code 22

Presence at memory of the module of management given DTC testifies to the fact of operation of safety any of face-to-face pillows, or натяжителя one of seat belts. Clearing of memory of the module thus is not represented possible, - replace the management module, worked pillow of safety, both lobbies of gauge SRS and натяжители seat belts of both seats.

Diagnostic code 23

Presence at memory of the module of management of the given code testifies to infringement of quality of contact connections of sockets of connection to the module of safety of face-to-face pillows of safety and натяжителей seat belts. Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see), then disunite sockets АВ6, АВ17 and АВ18 the module of management SRS and attentively study a condition of their contact plugs, also check up a condition of the plaits of electroconducting brought to sockets. In case of revealing of signs of development of corrosion of plugs replace the management module, the main plait of electroconducting, or the damaged electroconducting натяжителей seat belts.

Connect sockets and make sure of reliability of their fixing. Connect a negative wire to the battery and include ignition, - at infringement of serviceability of functioning of control lamp SRS replace the management module.

Diagnostic code 24

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite contact socket АВ6 of the module of management and connect to it a socket 1I diagnostic plait I1 or I2. Connect a negative wire to the battery, include ignition and measure pressure between the plug № 3 (+) a socket 2I a diagnostic plait and weight of the chassis. If the result of measurement makes more than 10 In, replace the management module, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite contact pair АВ1/В31 and connect to socket АВ1 a socket 2А A.Izmerte's diagnostic plait resistance between the plug № 9 sockets 5А a diagnostic plait And and the plug № 3 sockets 2I plait I/I2. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Measure resistance between plugs № 9 sockets 5А a plait And / № 3 sockets 2I plait I/I2 and weight of the chassis if results of measurements make more than 1 МОм, pass to the check final stage, otherwise replace the main plait of electroconducting SRS.

Make sure that ignition is switched off and take from the nest in the connecting block and examine a safety lock № 11. Fused safety lock replace. If the safety lock in norm, or a replaceable safety lock fuses at once again, find and debug a plait кузовной electroconducting.

Diagnostic code 25

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite contact socket АВ6 of the module of management and connect to it a socket 1I diagnostic plait I1 or I2. Connect a negative wire to the battery, include ignition and measure pressure between the plug № 6 (+) a socket 2I a diagnostic plait and weight of the chassis. If the result of measurement makes more than 10 In, replace the management module, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite contact pair АВ1/В31 and connect to socket АВ1 a socket 2А A.Izmerte's diagnostic plait resistance between the plug № 1 socket 5А a diagnostic plait And and the plug № 6 sockets 2I plait I/I2. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Measure resistance between plugs № 1 socket 5А a plait And / № 6 sockets 2I plait I/I2 and weight of the chassis if results of measurements make more than 1 МОм, pass to the check final stage, otherwise replace the main plait of electroconducting SRS.

Make sure that ignition is switched off and take from the nest in the connecting block and examine a safety lock № 6. Fused safety lock replace. If the safety lock in norm, or a replaceable safety lock fuses at once again, find and debug a plait кузовной electroconducting.

Diagnostic code 31

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite the central socket АВ6 of electroconducting of the module of management SRS and connect it to a socket 1I diagnostic plait I/I2. Measure resistance between plugs №№ 2 and 4 sockets 3I plait I/I2. If the result of measurement falls outside the limits a range 750 ч 1000 Ohm, pass to a following stage of check, otherwise replace the module of management SRS.

Measure resistance between plugs №№ 2 and 4 sockets 3I plait I/I2 and weight of the chassis. If the result of measurement makes less than 1 МОм, pass to a following stage of check, otherwise replace the management module.

Disunite socket АВ16 of electroconducting of right forward gauge SRS, connect to it a socket 1Н diagnostic plait Н and measure between plugs №№ 2 and 4 sockets 3I plait I/I2 and plugs №№ 5 and 6 (accordingly) a socket 3Н N.Esli's plait the result of measurement makes more than 10 Ohm, the following stage of check can be lowered.

Measure resistance between plugs №№ 2 both 4 sockets 3I and weight of the chassis. If the result of measurement makes less than 1 МОм, pass to a following stage of the check, otherwise following four stages can be lowered.

Remove a combination of devices (see Has undressed Removal, service and installation of a combination of devices, check of a condition of components) and disunite contact pair АВ14/АВ15 and connect a socket 2F diagnostic plait F to socket АВ14. Measure resistance between plugs №№ 2 and 4 sockets 3I plait I/I2 and plugs №№ 6 and 5 (accordingly) a socket 3F plait F, - if the result of measurement makes less than 1 МОм, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Measure resistance between plugs №№ 2 and 4 sockets 3I plait I/I2 and weight of the chassis, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Connect a socket 1F plait F to socket АВ15 and measure resistance between plugs №№ 3 and 4 sockets 3F plait F and plugs № 5 and 6 (accordingly) a socket 3Н N.Esli's plait the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of right forward gauge SRS.

Measure resistance between weight and plugs №№ 3 and 4 sockets 3F plait F and weight of the chassis, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of right forward gauge SRS.

Connect a socket 2Н plait Н to the right forward gauge SRS and measure resistance between the plug № 3 and the plug № 4 sockets 3Н a plait. If the result of measurement does not fall outside the limits a range 750 ч 1000 Ohm, pass to the check final stage, otherwise replace the gauge.

Measure resistance between plugs №№ 3 both 4 sockets 3Н and weight of the chassis, - if the result of measurement makes less than 1 МОм, replace the right forward gauge SRS.

Diagnostic code 32

The remark: the Description of procedures of removal/installation of working components and plaits of electroconducting SRSприведено in Section Removal and installation of components SRS.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite the central socket АВ6 of electroconducting of the module of management SRS and connect it to a socket 1I diagnostic plait I/I2. Measure resistance between plugs №№ 1 and 3 sockets 3I plait I/I2. If the result of measurement falls outside the limits a range 750 ч 1000 Ohm, pass to a following stage of check, otherwise replace the module of management SRS.

Measure resistance between plugs №№ 1 and 3 sockets 3I plait I/I2 and weight of the chassis. If the result of measurement makes less than 1 МОм, pass to a following stage of check, otherwise replace the management module.

Disunite socket АВ13 of electroconducting of left forward gauge SRS, connect to it a socket 1Н diagnostic plait Н and measure between plugs №№ 3 and 1 socket 3I plait I/I2 and plugs №№ 5 and 6 (accordingly) a socket 3Н N.Esli's plait the result of measurement makes more than 10 Ohm, the following stage of check can be lowered.

Measure resistance between plugs №№ 3 both 1 socket 3I and weight of the chassis. If the result of measurement makes less than 1 МОм, pass to a following stage of the check, otherwise following four stages can be lowered.

Remove a combination of devices (see Has undressed Removal, service and installation of a combination of devices, check of a condition of components) and disunite contact pair АВ11/АВ12 and connect a socket 2F diagnostic plait F to socket АВ11. Measure resistance between plugs №№ 3 and 1 socket 3I plait I/I2 and plugs №№ 6 and 5 (accordingly) a socket 3F plait F, - if the result of measurement makes less than 1 МОм, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Measure resistance between plugs №№ 3 and 1 socket 3I plait I/I2 and weight of the chassis, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace the main plait of electroconducting SRS.

Connect a socket 1F plait F to socket АВ12 and measure resistance between plugs №№ 3 and 4 sockets 3F plait F and plugs № 5 and 6 (accordingly) a socket 3Н N.Esli's plait the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of left forward gauge SRS.

Measure resistance between weight and plugs №№ 3 and 4 sockets 3F plait F and weight of the chassis, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of left forward gauge SRS.

Connect a socket 2Н plait Н to the left forward gauge SRS and measure resistance between the plug № 3 and the plug № 4 sockets 3Н a plait. If the result of measurement does not fall outside the limits a range 750 ч 1000 Ohm, pass to the check final stage, otherwise replace the gauge.

Measure resistance between plugs №№ 3 both 4 sockets 3Н and weight of the chassis, - if the result of measurement makes less than 1 МОм, replace the right forward gauge SRS.

Diagnostic code 41

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ26 emergency натяжителя a seat belt of a passenger seat. Disunite contact pair АВ24/АВ25 and connect to socket АВ24 a socket 1F diagnostic plait F. To a socket 3F a plait connect feigning resistor SRS. Connect a negative wire to the battery and include ignition, - at serviceable functioning of control lamp SRS replace the module of the right lateral pillow of safety, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact socket АВ18 of the module of management and connect to it a socket 1I diagnostic plait I/I2. Measure resistance between plugs №№ 7 and 9 sockets 3I plait I/I2 and plugs №№ 3 and 4 (accordingly) a socket 3F plait F, - if the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Measure resistance between plugs № 7 and № 9 sockets 3I. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Measure resistance between plugs № 3 and № 4 sockets 3F. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Measure resistance between plugs №№ 3 both 4 sockets 3F and weight of the chassis. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Measure resistance between plugs №№ 7 both 9 sockets 3I and weight of the chassis. If the result of measurement makes more than 1 МОм, replace the module of management SRS, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Diagnostic code 42

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ21 emergency натяжителя a seat belt of a driver's seat. Disunite contact pair АВ19/АВ20 and connect to socket АВ19 a socket 1F diagnostic plait F. To a socket 3F a plait connect feigning resistor SRS. Connect a negative wire to the battery and include ignition, - at serviceable functioning of control lamp SRS replace the module of the left lateral pillow of safety, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact socket АВ17 of the module of management and connect to it a socket 1I diagnostic plait I/I2. Measure resistance between plugs №№ 10 and 12 sockets 3I plait I/I2 and plugs №№ 3 and 4 (accordingly) a socket 3F plait F, - if the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Measure resistance between plugs № 10 and № 12 sockets 3I. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Measure resistance between plugs № 3 and № 4 sockets 3F. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Measure resistance between plugs №№ 3 both 4 sockets 3F and weight of the chassis. If the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Measure resistance between plugs №№ 10 both 12 sockets 3I and weight of the chassis. If the result of measurement makes more than 1 МОм, replace the module of management SRS, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Diagnostic code 45

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact socket АВ18 of the module of management and connect to it a socket 1I diagnostic plait I/I2. Connect a negative wire to the battery, include ignition and measure pressure between plugs №№ 7 and 9 sockets 3I plait I/I2 and weight of the chassis, - if the result of measurement makes less than 1 In, replace the module of management SRS, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Diagnostic code 46

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact socket АВ17 of the module of management and connect to it a socket 1I diagnostic plait I/I2. Connect a negative wire to the battery, include ignition and measure pressure between plugs №№ 10 and 12 sockets 3I plait I/I2 and weight of the chassis, - if the result of measurement makes less than 1 In, replace the module of management SRS, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Diagnostic code 51

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ26 emergency натяжителя a seat belt of a passenger seat. Disunite contact pair АВ24/АВ25 and socket АВ18 of the module of management SRS. Connect to socket АВ18 a socket 1I diagnostic plait I/I2. Disunite socket АВ28 of the module of the right lateral pillow of safety, connect to it a socket 1G diagnostic plait G and measure resistance between plugs №№ 17, 18, 19 and 20 sockets 3I plait I/I2 and plugs №№ 2, 4, 1 and 5 (accordingly) a socket 3G plait G. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Measure resistance between plugs №№ 17, 18, 19 both 20 sockets 3I and weight of the chassis, - if the result of measurement makes more than 1 МОм, replace the right lateral gauge SRS, otherwise replace burn down electroconductings of the right lateral pillow of safety.

Diagnostic code 52

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ21 emergency натяжителя a seat belt of a passenger seat. Disunite contact pair АВ19/АВ20 and socket АВ17 of the module of management SRS. Connect to socket АВ17 a socket 1I diagnostic plait I/I2. Disunite socket АВ23 of the module of the right lateral pillow of safety, connect to it a socket 1G diagnostic plait G and measure resistance between plugs №№ 5, 14, 15 and 16 sockets 3I plait I/I2 and plugs №№ 5, 1, 4 and 2 (accordingly) a socket 3G plait G. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Measure resistance between plugs №№ 5, 14, 15 both 16 sockets 3I and weight of the chassis, - if the result of measurement makes more than 1 МОм, replace the left lateral gauge SRS, otherwise replace burn down electroconductings of the left lateral pillow of safety.

Diagnostic code 53

Presence at memory of the block of self-diagnostics of a code 53 means necessity of performance of replacement of the gauge of the right lateral pillow of safety (the Section System of additional safety (SRS) - the device and a functioning principle see). In summary do not forget to activate SRS and to check up serviceability of its functioning on operation of a control lamp (the Section System of additional safety (SRS) - the device and a functioning principle see).

Diagnostic code 54

Presence at memory of the block of self-diagnostics of a code 54 means necessity of performance of replacement of the gauge of the left lateral pillow of safety (the Section System of additional safety (SRS) - the device and a functioning principle see). In summary do not forget to activate SRS and to check up serviceability of its functioning on operation of a control lamp (the Section System of additional safety (SRS) - the device and a functioning principle see).

Diagnostic code 55

The code 55 is highlighted at operation right lateral pillows of safety of a pillow and is not subject to removal from memory of the module of management. Replace a back of a forward seat with the worked pillow of safety, and also the corresponding lateral gauge and the module of management SRS. In summary do not forget to activate SRS and to check up serviceability of its functioning on operation of a control lamp (the Section System of additional safety (SRS) - the device and a functioning principle see).

Diagnostic code 61

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ26 emergency натяжителя a seat belt of a passenger seat and connect to it a socket 1F diagnostic plait F. To a socket 3F a plait connect feigning resistor SRS. Connect a negative wire to the battery and include ignition, - at serviceable functioning of control lamp SRS replace натяжитель a seat belt of a passenger seat (the Body see the Head), otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact pair АВ25/АВ24 and sockets АВ17 and АВ18 the management module. Connect to socket АВ18 a socket 1I diagnostic plait I/I2 and measure resistance between plugs №№ 8 and 6 sockets 3I plait I/I2 and plugs №№ 4 and 3 (accordingly) a socket 3F plait F. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of a lateral pillow of safety.

Measure resistance between plugs № 8 and № 6 sockets 3I, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of a lateral pillow of safety.

Measure resistance between plugs №№ 8 both 6 sockets 3F and weight of the chassis, - if the result of measurement makes more than 1 МОм, replace the module of management SRS, otherwise replace burn down electroconductings of a lateral pillow of safety.

Diagnostic code 62

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disunite socket АВ21 emergency натяжителя a seat belt of a driver's seat and connect to it a socket 1F diagnostic plait F. To a socket 3F a plait connect feigning resistor SRS. Connect a negative wire to the battery and include ignition, - at serviceable functioning of control lamp SRS replace натяжитель a seat belt of a driver's seat, otherwise pass to a following stage of check.

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact pair АВ19/АВ20 and sockets АВ17 and АВ18 the management module. Connect to socket АВ17 a socket 1I diagnostic plait I/I2 and measure resistance between plugs №№ 11 and 13 sockets 3I plait I/I2 and plugs №№ 4 and 3 (accordingly) a socket 3F plait F. If the result of measurement makes less than 10 Ohm, pass to a following stage of check, otherwise replace burn down electroconductings of a lateral pillow of safety.

Measure resistance between plugs № 11 and № 13 sockets 3I, - if the result of measurement makes more than 1 МОм, pass to a following stage of check, otherwise replace burn down electroconductings of a lateral pillow of safety.

Measure resistance between plugs №№ 11 both 13 sockets 3F and weight of the chassis, - if the result of measurement makes more than 1 МОм, replace the module of management SRS, otherwise replace burn down electroconductings of a lateral pillow of safety.

Diagnostic code 65

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact pair АВ25/АВ24 and sockets АВ17 and АВ18 the management module. Connect to socket АВ18 a socket 1I diagnostic plait I/I2. Connect a negative wire to the battery, include ignition and measure pressure between plugs №№ 6 and 8 sockets 3I plait I/I2 and weight of the chassis. If the result of measurement makes less than 1 In, replace the module of management SRS, otherwise replace burn down electroconductings of a lateral pillow of safety.

Diagnostic code 66

Disconnect SRS (the Section System of additional safety (SRS) - the device and a functioning principle see). Disconnect from a diagnostic plait feigning resistor. Disunite contact pair АВ19/АВ20 and sockets АВ17 and АВ18 the management module. Connect to socket АВ17 a socket 1I diagnostic plait I/I2. Connect a negative wire to the battery, include ignition and measure pressure between plugs №№ 11 and 13 sockets 3I plait I/I2 and weight of the chassis. If the result of measurement makes less than 1 In, replace the module of management SRS, otherwise replace burn down electroconductings of a lateral pillow of safety.