Subaru Legacy/Outback

1999-2003 of release

Repair and car operation


Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Details of a lining of onboard electroconducting
   System of additional safety (SRS) - the device and a functioning principle
   Diagnostics of malfunctions SRS
   Removal and installation of components SRS
   Control system of speed (темпостат) - the device and a functioning principle
   Check of serviceability of functioning of components and problem diagnostics темпостата
   Removal, check of a condition and installation of components of a control system by speed
   Combination of devices - the general information and a principle of functioning of components
   Problem diagnostics of components of a combination of devices
   Removal, service and installation of a combination of devices, check of a condition of components
   Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, regenerative repair of a thermoelectric heating element
   Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, regenerative repair of a thermoelectric heating element
   Removal, check of a condition and installation of switches of management by functioning of the electric drive of regulators Glass lifts
   The electric drive of rear-view mirrors - check of serviceability of functioning
   Removal check and installation of the switch of management by functioning of the electric drive of external rear-view mirrors
   Removal, check of a condition and installation of the switch of management by functioning of the electric drive of the top hatch
   Removal, check of a condition and installation combined подрулевых switches
   Check of serviceability of functioning of electromotors of a drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on models Legacy of Universal/Outback
   Check of the relay and switches of lighting and alarm devices
   Removal and installation of lighting devices, replacement of lamps
   Removal, check of a condition and installation of small horns and the horn switch
   Check of a condition and replacement of contact group of the switch of ignition
   The uniform lock - the device, a functioning principle, diagnostics of malfunctions
   Removal, check of a condition and installation of components of the uniform lock
   System иммобилизации the engine - the device, a functioning principle, diagnostics of malfunctions
   Removal and installation of components of system иммобилизации the engine
   Removal and installation of assemblage of a radio receiver
   Removal and installation of loudspeakers
   Check of a condition and regenerative repair of the window aerial of a radio receiver
   Removal, installation and check of a condition of the antenna amplifier of a radio receiver
   Removal and installation прикуривателя
   + Schemes of electric connections

Removal, check of a condition and installation of components of the uniform lock

 Models of cars considered in the present Management are equipped by system of additional safety (SRS). Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Section System of additional safety (SRS) - the device and a functioning principle see). Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.


The module of management of the uniform lock

Removal and installation

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove a ware box (the Body see the Head).

3. Give a fixing nut and, having disconnected electroconducting, remove the module of management of the uniform lock complete with the management module темпостата.

4. Installation is made upside-down.


Element of a food of the transmitter of panel DU of the uniform lock

 In order to avoid failure of the printed-circuit board of the transmitter preliminary make self-grounding, undertaken a hand a metal element of any construction!


Removal

 PERFORMANCE ORDER

Turn out the fixing screw, uncover and take from a head of the ignition key an element of a food of the transmitter of panel DU.


Check

 PERFORMANCE ORDER

1. Measure pressure between poles of the removed element of a food.

 In 3 seconds of measurement pressure of an element falls more than to 1.8 Century

 In order to avoid a discharge of an element of a food duration of measurement should make no more than 5 seconds!

2. If the result of measurement makes less than 2 In, replace a food element.

 In 3 seconds of measurement pressure of an element falls more than to 1.8 Century


Registration of the new transmitter

 PERFORMANCE ORDER

 On one car can be registered simultaneously no more than three transmitters.

1. Remove a lateral overlay of a threshold of a driver's door (the Body see the Head) illustrations connect contact pair of a registration socket in the bottom part of a forward rack.
2. Unblock a door-lock.
3. Press the transmitter button twice, the door-lock should be blocked automatically, then again be unblocked that confirms successful end of registration of the first transmitter.
4. In case of need repeat procedure for registration of the second/third transmitter.
5. Having finished registration procedure, disunite contact pair of a registration socket and make sure of serviceability of functioning of again registered transmitters.
6. Establish components into place acting in film for the purpose of providing of access.


Activators of locks of forward doors

Removal and installation

 PERFORMANCE ORDER

1. Remove assemblage of a latch of the lock (see Has undressed Removal, installation and check of components замковых assemblages).

2. Turn out fixing bolts and remove the activator.

3. Installation is made upside-down. Make sure of serviceability of functioning of the activator.


Check

 PERFORMANCE ORDER

1. Disconnect from the activator electroconducting.

2. Connect the battery a positive pole to the plug № 2 contact sockets, and negative - to the plug № 4, - the activator should pass in the blocked condition.

3. At change of polarity of connection of the battery the activator should be unblocked.
4. The faulty activator is subject to replacement.


Activators of locks of back doors

Removal and installation

 PERFORMANCE ORDER

1. Remove assemblage of a latch of the lock (see Has undressed Removal, installation and check of components замковых assemblages).

2. Turn out fixing bolts and remove the activator.

3. Installation is made upside-down. Make sure of serviceability of functioning of the activator.


The activator of the lock of a door of a back (model Legacy of Universal/Outback)

Removal and installation

 PERFORMANCE ORDER

1. Remove assemblage of a latch of the lock (see Has undressed Removal, installation and check of components замковых assemblages).

2. Turn out fixing bolts and remove the activator.

3. Installation is made upside-down. Make sure of serviceability of functioning of the activator.


On the main page