Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
- Brake system
   Prorolling of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of brake system
   Replacement колодок disk brake mechanisms of forward wheels
   Replacement колодок disk brake mechanisms of back wheels
   Condition check, removal and installation of brake disks
   Removal, major repairs and installation of supports of disk brake mechanisms of forward wheels
   Removal, major repairs and installation of supports of disk brake mechanisms of back wheels
   Removal, major repairs and installation of the valve of management
   Removal and installation of a pedal of a foot brake
   Lay brake - the general data and adjustments
   Removal and installation of a control lever of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Removal and installation of the gauge-switch of stoplights
   System of antiblocking of brakes (ABS) - the general information
   Removal and installation of components of system of antiblocking of brakes
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Replacement of hoses and tubes of a hydraulic path of brake system

The preventions resulted in section Brake system see.


 PERFORMANCE ORDER

1. In case of need replacements of a hydraulic tube or a hose merge a liquid from hydraulic system (the Uniform hydraulic system see the Head). Alternatively minimisation of losses of a hydraulic liquid can be provided by a way пережимания flexible hoses, or fast закупоривания the disconnected brake tubes and their unions. Prepare to assemblage of a spilt liquid, having enclosed under corresponding штуцерное connection () polyethylene or rags.
2. In need of a detachment of a flexible brake hose, give its nut штуцерного connections with a rigid tube before to remove a spring collar of fastening of a hose on the arm.
3. To give накидные nuts штуцерных connections is better by means of special накидного a key with a cutting head (ask in shops of automobile accessories). At absence near at hand a special key it is possible to take advantage densely sitting down on шлицы nuts рожковым of a key, however in case of strongly tightened nut such way is connected with risk of a rounding off of corners шлицов nuts as a result of key failures. In that case it is necessary to try to give a nut with the help самоконтрящегося арматурного a key (Swede). In case of damage шлицов nuts it is subject to replacement in gathering with the tube. Before a partition штуцерного connections always carefully wipe it outside in order to avoid hit in dirt system. At undocking more than one connection try to remember an order of installation of removed sections precisely.
4. Replaceable brake tubes of various length with развальцованными the ends and put on накидными nuts can be got in company Citroyon services-centres. Having picked up section of the demanded length (corresponding removed) it is necessary to give only to it the necessary form for correct installation on the car. Alternatively, brake tubes can be made to order in a workshop of car-care centre of details let out by sets. It is necessary to measure only precisely length of the original removed from the car. Will be most correct to take an old tube with itself in shop or a workshop.
5. At installation do not tighten штуцерные a nut too hardly! Tightness of connection is not so proportional to effort of a tightening of its components, and is defined by correctness of their assemblage.

6. At replacement of flexible brake hoses pay attention to an admissibility of their use in contact to hydraulic liquid LHM. Track correctness of a lining of lines, do not suppose перекручивания hoses and watch, that they have been fixed in all provided arms and clamps.

7. Having finished installation of components, add in the tank of hydraulic system necessary quantity of a liquid of a demanded grade (address to the Head Routine maintenance) and pump over a path (Prorolling of hydraulic system see). Смойте traces of the spilt brake liquid also check up system on presence of signs of leaks.


On the main page