Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
- Brake system
   Prorolling of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of brake system
   Replacement колодок disk brake mechanisms of forward wheels
   Replacement колодок disk brake mechanisms of back wheels
   Condition check, removal and installation of brake disks
   Removal, major repairs and installation of supports of disk brake mechanisms of forward wheels
   Removal, major repairs and installation of supports of disk brake mechanisms of back wheels
   Removal, major repairs and installation of the valve of management
   Removal and installation of a pedal of a foot brake
   Lay brake - the general data and adjustments
   Removal and installation of a control lever of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Removal and installation of the gauge-switch of stoplights
   System of antiblocking of brakes (ABS) - the general information
   Removal and installation of components of system of antiblocking of brakes
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal, major repairs and installation of supports of disk brake mechanisms of back wheels

The preventions resulted in section Brake system see. At assemblage new sealing washers штуцерного a socket of a hydraulic tube be required.


Details of fixture of a support of the back brake mechanism

Pay attention that before removal the support should be fastened a fastening finger колодок

1 — the Hydraulic tube
2 — Bolts of fastening of a support
3 — a fastening Finger колодок
3 — the Nut of a fixing finger


Components of the brake mechanism of a back wheel

1 — the Brake board and a filter колодок
2 — the Piston with cuffs
3 — the Finger of fastening brake колодок
4 — Antivizgovaja a spring
5 — Brake колодка (internal)
6 — the Support of the brake mechanism
7 — the Brake disk

Removal

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Remove a corresponding wheel.
3. Dump pressure in hydraulic system for what ослабьте спускной the regulator gate (the Uniform hydraulic system see the Head) and translate a control lever a suspension bracket in position "Minimum".
4. Remove brake Pads (Replacement колодок disk brake mechanisms of back wheels see).
5. Fasten among themselves two half of support, having established into place a fastening bolt колодок and strongly having tightened its nut.
6. Get drain capacity under the connection union to a support of a hydraulic tube. Release штуцерный a socket and disconnect a tube from a support. At once закупорьте the open ends of a tube and the union for the purpose of minimisation of losses of a hydraulic liquid and in order to avoid hit in dirt system.
7. Turn out two fixing bolts and remove support assemblage (see an illustration of the Detail of fixture of a support of the back brake mechanism).

Major repairs

Performance of regenerative repair of the failed support probably only with application firm ремнабора companies Citroyon. Track, that ремнабор corresponded to type of the support removed from the car. Pay attention to correctness of installation of each of components. New linings and уплотнители before installation grease with a hydraulic liquid. In the rest follow instructions of manufacturers. The design of the brake mechanism is presented on an illustration Components of the brake mechanism of a back wheel.

Installation

 PERFORMANCE ORDER

1. Grease a carving of fixing bolts, then establish a support on the regular place, screw bolts and tighten them with demanded effort.
2. Connect to a support a hydraulic tube (do not forget to replace sealing washers). Strongly tighten штуцерный a socket.
3. Give a nut and take from a support a fastening finger колодок.
4. Establish into place brake Pads (Replacement колодок disk brake mechanisms of back wheels see).
5. Establish a wheel.
6. Tighten спускной the gate of a regulator of pressure (the Uniform hydraulic system see the Head) and translate a control lever a suspension bracket in position “Normal driving” (Normal movement).
7. Lower the car on the earth and tighten wheel bolts with demanded effort.


On the main page