Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
- Brake system
   Prorolling of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of brake system
   Replacement колодок disk brake mechanisms of forward wheels
   Replacement колодок disk brake mechanisms of back wheels
   Condition check, removal and installation of brake disks
   Removal, major repairs and installation of supports of disk brake mechanisms of forward wheels
   Removal, major repairs and installation of supports of disk brake mechanisms of back wheels
   Removal, major repairs and installation of the valve of management
   Removal and installation of a pedal of a foot brake
   Lay brake - the general data and adjustments
   Removal and installation of a control lever of a lay brake
   Removal and installation of cables of a drive of a lay brake
   Removal and installation of the gauge-switch of stoplights
   System of antiblocking of brakes (ABS) - the general information
   Removal and installation of components of system of antiblocking of brakes
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal, major repairs and installation of the valve of management

The preventions resulted in section Brake system see. At assemblage new sealing washers штуцерного a socket of a hydraulic tube be required.


Cross-section of the valve of management of brake system

1 — the Union of connection of a returnable tube
2 — the Exit forward brake a contour
3 — Zaglushka with a yellow ring
4 — the Union of connection of a returnable tube
5 — the Admission of a liquid being under a high pressure
6 — To a hydraulic path of a back suspension bracket
7 — the Exit of a back brake contour

Removal

 PERFORMANCE ORDER

1. On models with a link sided steering remove the tank of a hydraulic liquid (the Uniform hydraulic system see the Head) and an arm of its fastening.
2. On some models for the purpose of providing of access to the valve it is necessary to remove some stirring components, including a cover of a head of cylinders.
3. Try to remember an order of connection and a route of a lining brought to клапанной to assemblage of hydraulic lines.

4. Release штуцерные sockets and disconnect from клапанной assemblages hydraulic tubes. Prepare for gathering of a spilt liquid. At once закупорьте the open ends of tubes and unions for the purpose of minimisation of losses of a liquid and in order to avoid hit in dirt system.

5. Turn out bolts of fastening of the valve.
6. Release fixing муфту клапанной assemblages.
7. Release fixing collars and disconnect from the valve two hydraulic hoses.

At assemblage шланговые collars are subject to replacement without fail.

8. Take assemblage of the valve of management from an impellent compartment.

Major repairs

Performance of regenerative repair of the failed valve of management is possible only with application firm ремнабора companies Citroyon. Track correctness of installation of each of components. New linings and уплотнители before installation grease with a pure hydraulic liquid. In the rest follow instructions of manufacturers. The design of the valve of management of brake system is presented on an illustration the Cross-section of the valve of management of brake system.

Installation

 PERFORMANCE ORDER

1. Connect to клапанной to assemblage hydraulic hoses and fix them on the unions new collars.
2. Connect to the valve hydraulic tubes (do not forget to replace sealing washers штуцерных sockets). Do not tighten sockets at the given stage. Track correctness of connection of hydraulic lines.
3. Get клапанную assemblage on the regular place in an impellent compartment of the car and tighten муфту its fastenings.
4. Screw two fixing bolts and tighten them with demanded effort.
5. Make sure of correctness of a lining of hydraulic lines and strongly tighten штуцерные sockets.
6. Establish components acting in film for the purpose of providing of access.
7. On models with a link sided steering establish into place the tank of a hydraulic liquid with a fixing arm (the Uniform hydraulic system see the Head).
8. Pump over hydraulic system (Prorolling of hydraulic system see).


On the main page