Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and the car bottom
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Removal and installation of a forward bumper
   Removal and installation of a back bumper
   Removal, installation and cowl adjustment
   Removal and installation drive a cable отпускания the cowl lock
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators Glass lifts door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive door Glass lifts
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External кузовная furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and installation of the panel of devices
   Control кузовные the sizes
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of panels of an internal upholstery of doors

Forward doors

Removal

 PERFORMANCE ORDER

1. Open a door and approximately on two third lower a windowpane. Disconnect a negative wire from the battery.

2. Extend the button of deenergizing of the lock, then by means of a small screw-driver wring out a lock uvula and definitively remove the button.

3. On models with a manual drive Glass lifts remove the handle of management from the spindle, then remove a facing plate.

4. Turn out the screw located in the bottom back end of facing of the internal handle of a door.

5. Accurately having hooked, remove from the handle the facing panel. At a corresponding complete set, delay the panel of an internal upholstery from a doorframe and disunite contact sockets of electroconducting of a drive steklopodemnika / a door rear-view mirror. If door mirrors are equipped by a manual drive, remove from the panel of an internal upholstery decorative furnish drive the mechanism.

6. Turn out two bottom screws of fastening of an armrest.

7. Through an aperture in the door handle turn out the top screw of fastening of an armrest (pay attention that the internal handle is a part of a design of an armrest).

8. Turn out the screw of fastening of the panel of the internal upholstery, located with the forward party of an aperture of the internal handle.

9. Accurately having hooked a screw-driver, remove the panel of a cover of a loudspeaker.

10. Turn out three screws of fastening of the panel of the internal upholstery, located around dynamics of a loudspeaker.

11. Hooking approaching вильчатым the tool, release the doors located on perimetre clamps and remove the panel of an internal upholstery (do not forget to disconnect electroconducting from a loudspeaker).

12. If there is a necessity for removal of the plastic sealing screen, it is necessary to dismantle preliminary the internal handle (Removal and installation of door handles and lock components see) and, at a corresponding complete set, the block of management of the electric drive window lifterа:
   a) the Block of management of the electric drive window lifterа fastens two screws used also for fixing Pads of contact sockets of electroconducting. Disconnect electroconducting, then turn out screws and remove the block;
   b) Liberate contact sockets from Pads and remove last;
   c) On the models equipped with the anticreeping alarm system, disunite a contact socket of electroconducting of the gauge of tracking (the gauge is built in in the decorative panel of furnish of a door mirror).

13. Accurately separate the sealing screen from a doorframe (if the screen is not replaced, try not to damage a film). At screen removal pass electroconducting plaits through apertures through passage in it.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down. Pay attention to following moments:
   a) Replace the panels of an internal upholstery damaged in the course of dismantle fixing clamps;

   b) Make sure, that the coupling screw of an executive rod of a door-lock after installation of the internal handle has been tightened;

   c) At installation of the button of deenergizing of the lock at first close a door and make sure that the executive rod of the switch is in the bottom position. Translate a lock uvula in bottom of two apertures, then densely plant the button on the rod end (before click), - the lock uvula thus should appear in the top aperture.

Back doors

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a door.
3. Execute the procedures described in subsection "Forward doors - Removal", subitem 2-11.
4. In need of removal of the plastic sealing screen at first release fastening clamps on a door of a basic arm of electroconducting.

Installation

The subsection "Forward doors - Installation" see.


On the main page