Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and the car bottom
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Removal and installation of a forward bumper
   Removal and installation of a back bumper
   Removal, installation and cowl adjustment
   Removal and installation drive a cable отпускания the cowl lock
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators Glass lifts door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive door Glass lifts
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External кузовная furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and installation of the panel of devices
   Control кузовные the sizes
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of components of the lock of a door of a back

Lock assemblage

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a back door
3. Open лючки access and disconnect electroconducting from assemblages of the back combined lanterns built in at a door.

4. Remove clamps.
Bверху Extraction of the central pin of a clamp
Below Extraction of a clamp of fastening of the finishing panel of a door of a back



5. Turn out fixing screws.

6. Remove the bottom panel of furnish of a door of a back.

7. Mark position of heads of bolts of fastening замковой assemblages.

8. Turn out two fixing bolts and remove lock assemblage, having disconnected from it an executive rod.

Installation

Installation is made upside-down. Pay attention to following moments:
   a) Track correctness of installation of fixing bolts (according to the labels put in the course of dismantle);
   b) Before installation to the place of the finishing panel make sure of serviceability of functioning of the lock. In case of need ослабьте fixing bolts and in appropriate way correct assemblage position. Having finished adjustment, strongly tighten fixing bolts and establish into place the furnish panel.

The lock cylinder

Removal

 PERFORMANCE ORDER

1. Execute the procedures described in subsection "lock Assemblage - Removal", subitem 1-4.
2. At a corresponding complete set screw two fixing bolts and remove the block of the activator of the uniform lock. Having removed the servo-driver, disconnect from the lock an executive rod and electroconducting.

3. Turn out three fixing screws, take sideways the cylinder of the lock from a door and disconnect the remained executive rod.

4. For extraction of the cylinder from assemblage remove пенопластовое a sealing ring, then insert a key into a keyhole and simultaneously release a lock uvula of fastening of the cylinder. For a key take the cylinder.

Installation

Installation is made upside-down. Track for correctness of installation and reliability of fastening of an executive rod.

The drummer of the lock

Removal

 PERFORMANCE ORDER

1. Remove covers and turn out screws of fastening of the back panel of an upholstery of a luggage space. Remove the panel, having provided with that access to the drummer of the lock.

2. Unbend back edge of a carpet covering and turn out two bolts of fastening of the drummer. At a corresponding complete set liberate from assemblage of the drummer the gauge-switch of the anticreeping alarm system.

Installation

Installation is made upside-down.

On the main page