|
1. Translate a control lever a suspension bracket in position "Maximum", then disconnect a negative wire from the battery.
2. Remove the central console (Removal and installation of the central console see).
3. Remove a steering wheel (address to the Head the Running gear and a steering).
4. Remove casings of a steering column (Removal and installation of elements of internal furnish of salon see). |
|
5. At a corresponding complete set find under a steering column contact sockets of electroconducting of a radio tape recorder and a pillow of safety and disunite them.
Contact sockets of electroconducting of a radio tape recorder (1) and pillows of safety (2) under a steering column |
|
|
6. By means of a screw-driver release the clamp located in the right top corner of the rotating drum-type socket, located on the centre of a steering column. |
|
|
7. Take a socket from a casing, having extended trace burn down electroconductings (in case of need remove right combined подрулевой the switch for unobstructed extraction of a plait). |
|
|
8. Turn out three fixing screws and remove a casing подрулевого the switch from a steering column. |
|
|
9. Open a cover of the assembly block of safety locks for the purpose of providing of access to the screw of fastening of the finishing panel located in the bottom corner of salon from the driver's party of the car. |
|
10. Turn out the top and bottom screws of fastening of the angular panel of furnish, then pull the panel forward and disconnect electroconducting of switches. Try to remember an order of connection of sockets, then remove the panel. |
|
|
11. Turn out three screws/release three clamps of fastening of the finishing panel of assemblage of the switches located under an instrument guard. Liberate a left-hand side of the panel from “торпедо”, then pull the panel forward and disconnect electroconducting from the switches built in in it (try to remember an order of connection of sockets). |
|
|
12. Remove the panel of switches. |
|
|
13. Having hooked a small screw-driver, accurately liberate from the top corners of the panel of devices (“торпедо”) panels of high-frequency loudspeakers. Disconnect from динамиков electroconducting. |
|
|
14. Through apertures under installation of loudspeakers liberate from clamps on the panel of devices contact sockets and electroconducting plaits. |
|
15. Turn out two bottom and one top the screw of fastening of an instrument guard. Extend a guard on itself and disconnect from its bottom part electroconducting. |
|
|
16. Remove a guard. |
|
|
17. Turn out fixing screws/release clamps and remove located under the panel of devices section of furnish of a forward wall of a driver's foot well.
18. Turn out two fixing screws on the left side of the panel of the bottom cover of a steering column. |
|
19. Turn out three remained screws of fastening of the panel of the bottom cover of a steering column/cover of the assembly block of safety locks. Access to screws is possible through a casing of the assembly block. Remove the panel. Where it is required, liberate from the panel electroconducting sockets. |
|
|
20. Disunite three contact sockets of electroconducting located under a steering column. |
|
|
21. Remove a steering column (address to the Head the Running gear and a steering). |
|
22. Take from the panel of devices an ashtray, then turn out two fixing screws in the bottom part of facing of control panels heater/radio tape recorder functioning, by means of a small screw-driver accurately release fixing clamps and remove facing. |
|
|
23. On models from the panel of devices located in the central part a radio tape recorder screw two fixing screws, then take assemblage of a radio tape recorder from the panel and disconnect brought its back part electroconducting and an antenna cable. |
|
24. Turn out four fixing screws and take from the panel of devices a radio tape recorder casing. Where it is required, liberate from a casing sockets of electroconducting and an antenna cable. |
|
|
25. At a corresponding complete set turn out four fixing screws and take from the central panel of devices a small ware shelf. |
|
26. Turn out two bottom fixing screws and take from the panel of devices an ashtray/prikurivatelja casing, having disconnected electroconducting from the last and lamps of illumination of assemblage. Remove a casing. |
|
|
27. Turn out four screws of fastening to “торпедо” control panels heater functioning. |
|
28. Accurately hooking a small screw-driver, remove from the panel of devices deflectors two central ventilating snuffled. |
|
|
29. Turn out two fixing screws and take assemblage of the central ventilating snuffled from the panel of devices. |
|
|
30. Disconnect electroconducting from switches in the central part of the panel of devices, hours and, at a corresponding complete set, - a control lamp/gauge of temperature of air in salon. |
|
|
31. Open a cover of a ware box, release a lock uvula in its back part, then completely lower a cover. Turn out six fixing screws. |
|
|
32. Take assemblage of a ware box from the panel of devices. |
|
|
33. Turn out fixing screws and remove a carpet upholstery under the panel приоров from the passenger party of the car. |
|
34. Hooking a small screw-driver, remove panels of furnish from lobbies кузовных racks. |
|
|
35. Remove assemblage of the electromotor of a drive of cleaners of a windscreen (address to the Head the Onboard electric equipment). |
|
36. From outside an impellent compartment turn out three nuts of fastening of the panel of devices to a partition. |
|
|
37. In car salon turn out the left screw of fastening of the bottom part of the panel. |
|
|
38. Then give two right screws. |
|
|
39. From both parties of the top arm of a steering column turn out two screws of fastening to it panels of devices. |
|
|
40. Also give two screws of fastening of the panel of devices to the bottom arm of a column. |
|
|
41. Through a niche under radio tape recorder installation turn out the top bolt of fastening of the panel of devices to heater assemblage. |
|
|
42. In the bottom part of the central section of the panel of devices turn out the bottom screw of fastening of a bearing frame of the panel to a heater. Also turn out the screw of fastening of the panel to the right bearing frame which is not subject to removal from the car. |
|
|
43. Through an aperture under radio tape recorder installation / a ware shelf (from its left party) turn out a bolt of fastening of a ventilating air line to the left bearing frame of the panel of devices. |
|
|
44. Under the central part of the panel turn out a bolt of fastening of its left bearing frame to an arm on a car floor. |
|
|
45. Where it is required, take the back relay from the assembly block of safety locks for the purpose of a possibility of removal of the panel of devices. |
|
|
46. By means of the assistant accurately delay assemblage of the panel of devices forward, separating it from a partition of an impellent compartment and liberating remained fixed electric sockets. Take the removed assemblage through one of an apron of doors of the car, passing electroconducting through apertures in it. Try to remember routes of a lining of plaits. |
|