Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and the car bottom
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Removal and installation of a forward bumper
   Removal and installation of a back bumper
   Removal, installation and cowl adjustment
   Removal and installation drive a cable отпускания the cowl lock
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators Glass lifts door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive door Glass lifts
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External кузовная furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and installation of the panel of devices
   Control кузовные the sizes
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of door rear-view mirrors and accompanying components

Mirrors with a manual drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (Removal and installation of panels of an internal upholstery of doors see).
2. Separate and unbend the top forward corner of the plastic sealing screen of a door for the purpose of providing of access to the plug through passage drive a cable of a regulator of position of a mirror. Take the plug from the door panel.
3. Having hooked, liberate from a corner of a door the panel of decorative furnish, at a corresponding complete set liberate from clamps on the panel the gauge of tracking of the anticreeping alarm system, then remove the panel.
4. Turn out five fixing screws and remove assemblage of a rear-view mirror from a door. Pass приводной a cable through an aperture at doors. Try to remember a route of a lining of a cable.

Installation

Installation is made upside-down. Track correctness of a lining drive a cable.

Mirrors with an electric drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (Removal and installation of panels of an internal upholstery of doors see).

2. Find the ends of a spring clamp of fastening of the glass located from an upper edge of assemblage of a mirror. Where it is required, remove the block of management of the electric drive window lifterа with колодкой a contact socket for the purpose of providing of access.

3. Take from the door panel the rubber plug of electroconducting through passage.

4. Having hooked, liberate from a corner of a door the panel of decorative furnish of knot of fastening of a mirror. At a corresponding complete set liberate from the panel the gauge of tracking of the anticreeping alarm system, then remove the panel.

5. Walk on a plait of electroconducting from a mirror to Pads and disunite contact sockets. At a corresponding complete set disconnect also electroconducting of the temperature gauge.

6. Turn out five fixing screws and remove assemblage of a mirror from a door. Liberate from a door burn down electroconductings.





Installation

Installation is made upside-down. Track correctness of a lining and reliability of fastening of electroconducting.

Mirror glass

Removal

 PERFORMANCE ORDER

1. Glass fastens in assemblage of a mirror by means of a metal spring clamp.
2. Find the ends of a clamp of fastening of the glass located from an upper edge of assemblage of a mirror. Where it is required, remove the block of management of the electric drive window lifterа with колодкой a contact socket for the purpose of providing of access.

3. Hook the ends of a clamp a screw-driver for the purpose of clearing of glass of a mirror.

4. Remove glass, at a corresponding complete set disconnect electroconducting. Remove from assemblage a spring clamp if it is planted freely.
A — Contact sockets of electroconducting
B — the Spring clamp

Installation

 PERFORMANCE ORDER

1. Establish a spring clamp on the back party of glass of a mirror. Track, that the clamp ends have entered in the correct image into glass grooves.
2. Fill glass in assemblage of a mirror to защелкивания a clamp in an adjusting flute.

For simplification of landing of a clamp preliminary slightly grease a plastic ring on a regulator.

The switch of management of the electric drive of adjustment of position of a door mirror

The Onboard electric equipment see the Head.

On the main page