Citroen Xantia

Since 1993 of release

Repair and car operation

Removal and installation of seat belts

Try to remember adjusting positions of various washers and the remote plugs used in анкерных knots of fastening of belts.

Seat belts of forward seats

Removal

PERFORMANCE ORDER

1. Accurately having hooked, remove the decorative panel from external edge of a forward seat. Delay the panel forward, then submit it to a door and remove from a seat. 2. Turn out a bolt of fastening of the bottom anchor of a belt to a seat frame.
3. Having hooked, uncover with top анкерного a belt bolt on central кузовной to a rack.
4. In the bottom part of the central rack turn out two screws of fastening of the panel of its furnish. Pull together from panel edges sealing strips, then remove the panel from a rack.
5. Turn out a fixing bolt and remove from a rack top анкерную belt assemblage.
6. Turn out a bolt of fastening of an inertial drum of the returnable device and remove assemblage of a seat belt from the car.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs анкерных knots and durability of a tightening of fixture.

Stem holders of buckles of forward seat belts (model without натяжителей belts)

Removal

PERFORMANCE ORDER

1. Turn out fixing screws/release clamps and remove the lateral panel of furnish of a seat.
2. The holder fastens a bolt to a seat frame. Under a bolt head the washer (do not forget about it) is enclosed.

Installation

Installation is made upside-down. Track durability of a tightening of fixture.

Stem holders of buckles of forward seat belts (model with натяжителями belts)

On the models equipped with system of a pretightness of forward seat belts it is necessary to make a small spadework:
   a) Take the ignition key;
   b) Disconnect a negative wire from the battery and wait about 10 minutes;
   c) Disunite a contact socket of electroconducting of the device of a pretightness (sockets are painted in orange colour and are located under seats).

Do not undertake attempts of diagnosing of blocks of a pretightness of belts. Remember that giving of any power supplies (including a current developed by the internal power supply of an ohmmeter) leads to operation of mechanisms of the device of a pretightness. Besides, operation of devices occurs also at a warming up of assemblages to temperature above 100°С.

Removal

PERFORMANCE ORDER

1. The holder is built in the mechanism натяжителя a seat belt. 2. Turn out fixing screws/release holders and remove the lateral panel of furnish of a seat. 3. Liberate electroconducting натяжителя from clamps on the bottom party of a seat.
4. Loosen the the forward screw of fastening натяжителя. 5. Turn out a back fixing bolt. A — the Forward screw B — the Back bolt
6. Remove the mechanism натяжителя from a seat.

Try not to touch with hands a buckle or a cable, - hold натяжитель for the case.

Installation

Installation is made upside-down. Pay attention to following moments:
a) Before installation натяжителя make sure that the storage battery is disconnected, and ignition is switched off;
b) Try not to touch a seat belt buckle at the first inclusion of ignition.

Lateral seat belts of a back seat

Removal

PERFORMANCE ORDER

1. Open a door of a back and a back door of the car from the corresponding party of the car. Remove sealing strips in edges of the panel of internal furnish of back lateral section of a body.
2. Hooking the panel of internal furnish of a back rack liberate it from clamps and remove (pay attention that the panel is latched in persistent section of a back shelf).
3. Turn out a bolt of fastening top анкерного seat belt knot to a back rack. 4. Combine forward a pillow of a seat for the purpose of providing of access to bottom анкерному to a belt bolt. Turn out a bolt.
5. Having hooked, liberate window facing under a seat belt from the lateral panel of internal furnish of salon, then pass through the panel top and bottom анкерные belt knots.
6. Отболтите an inertial drum of the returnable device also remove assemblage of a seat belt from the car.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs анкерных knots and behind durability of a tightening of fixture.

The central seat belt of a back seat

Removal

PERFORMANCE ORDER

1. Assemblage simply приболчена to the panel of a floor of the car, - lift a seat pillow.

Installation

Installation is made upside-down. Track correctness of installation of washers and remote plugs анкерных knots and behind durability of a tightening of fixture.

The electronic block of management натяжителей forward seat belts

Removal

The block is located under the central console.

PERFORMANCE ORDER

1. Disconnect a negative wire from the battery and wait not less than 10 minutes. 2. Remove the central console (Removal and installation of the central console see). 3. Disunite contact sockets of electroconducting. Try to remember routes of a lining of plaits.
4. Give four fixing nuts and remove the block of management from a basic arm.

Installation

Installation is made upside-down. Track correctness of a lining of electroconducting and reliability of fastening of contact sockets before to connect the storage battery.

On the main page