Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
- Suspension bracket and steering
   Specifications
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Design and principle of functioning of elements of the hydrostrengthened steering drive - the general information
      Adjustable safety steering column - the general information
      Removal and steering wheel installation
      Removal, check of a condition and installation карданного the hinge of a steering column
      Removal, service and installation of a steering column
      Removal, service and installation of the steering mechanism
      Removal, installation and check of a condition of elements of hydraulic path ГУР
      Removal, service and installation of the steering pump
      Removal and installation of the tank of liquid ГУР
      Check and replacement of liquid ГУР, removal of air from a hydraulic path
   + Wheel assemblages, suspension bracket geometry
+ Body
+ Onboard electric equipment

Removal, service and installation of a steering column

 The description of procedures of removal/installation of assemblage combined подрулевых switches is resulted in the Head the Onboard electric equipment.


Details of installation of a steering column

1 — the Safety steering column
2 — Kardannyj the hinge

Efforts of a tightening of carving connections, Nanometer

Т1: 24
Т2: 25

REMOVAL

 PERFORMANCE ORDER

1. Tyre out the car on the lift.
2. Disconnect a negative wire from the battery.
3. Remove the module of a driver's pillow of safety (the Onboard electric equipment see the Head).
4. Remove a steering wheel (see Has undressed Removal and steering wheel installation).
5. Lift the car over the earth and remove карданный the hinge of a steering shaft (see Has undressed Removal, check of a condition and installation карданного the hinge of a steering column).
6. Lower the car and remove section of the bottom furnish of the panel of devices from the driver's party of salon.

7. Turn out the screw of fastening of the bottom cover of a casing of a steering column.

8. Disunite contact sockets of all plaits of electroconducting brought to a steering column.

9. Turn out two devices of a bolt of fastening of a steering column located under the panel.

10. Liberate assemblage of a steering shaft from a foot emphasis of a floor.

DISMANTLING

 PERFORMANCE ORDER

 The description of procedures of removal/installation combined подрулевых switches is resulted in the Head the Onboard electric equipment.

Turn out two screws of fastening of the top cover of a casing of a steering column, and also two screws of fastening of assemblage combined подрулевых switches, and remove corresponding components.

ASSEMBLAGE

 PERFORMANCE ORDER

1. Establish on the top shaft of a column assemblage of the combined switches.
2. Establish the top cover, then pass electroconducting plaits подрулевых switches and the ignition switch between basic to ledges of a cover and tighten fixing screws with demanded effort (1.2 Nanometers).

CHECK

 PERFORMANCE ORDER

1. Carefully wipe external surfaces of components of assemblage of a steering column pure rags and study their condition. Defective details replace.

2. Measure full length of assemblage of a steering column. If the result of measurement falls outside the limits an admissible range (849.7 mm: for models Legacy and 817.8 mm: for models Outback), replace assemblage.

INSTALLATION

 PERFORMANCE ORDER

1. Fill the plug through passage in the panel of a foot emphasis.

2. Pass the end of a steering shaft in the plug through passage.
3. Tighten with demanded effort (25 Nanometers) located under the panel of devices bolts of fastening of a steering column.
4. Restore initial connection of the devices of plaits of electroconducting laid under the panel.
5. Connect a socket of electroconducting of a pillow of safety on a cable drum, - track for защелкиванием the double lock.
6. Keeping the lever of adjustment of an inclination of a column in the lowered position, establish the bottom cover of a casing of a steering column.
7. Connect карданный the hinge (see Has undressed Removal, check of a condition and installation карданного the hinge of a steering column).
8. Centre position of a contact drum of a chain of electroconducting of a horn/pillow of safety (the Onboard electric equipment see the Head), - track, that forward wheels of the car were in rectilinear position.
9. Establish and adjust a steering wheel (see Has undressed Removal and steering wheel installation) and the module of a driver's pillow of safety (the Onboard electric equipment see the Head).


On the main page