Subaru Legacy/Outback

1999-2003 of release

Repair and car operation


Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
- The power supply system and release
   Specifications
   - System of injection of fuel
      Sbrasyvanie pressure in the power supply system
      Опорожнение a fuel tank
      Check of a condition and replacement of fuel lines and them штуцерных connections
      Service of components of an inlet air path
      Removal and installation of the case of a throttle
      Service of components of a drive throttle заслонки
      Removal, service and installation of the inlet pipeline
      Service of the fuel pump
      Removal and installation of main relay MFI
      Removal and installation of the relay of the fuel pump
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of the gauge of level of fuel in the additional chamber of a fuel tank
      Removal, check and installation of the fuel filter
      Removal and installation запорного the valve отсечки fuel
      Removal and installation демпфирующих fuel valves
      Removal and installation of a fuel tank
      Removal and installation of a jellied mouth of a fuel tank
      Removal and installation of components of system of injection of fuel
   + Control systems of the engine and decrease in toxicity of the fulfilled gases
   + System of release of the fulfilled gases
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of a jellied mouth of a fuel tank

Design of a jellied mouth of a fuel tank

1 — the Main hose of a jellied mouth
2 — the Collar
3 — the Collar
4 — the Sealing lining
5 — the Fixing flange
6 — the Cover

7 — the Protector

Efforts of a tightening of carving connections, Nanometer

Т: 7.4

REMOVAL

 PERFORMANCE ORDER

1. Tyre out the car on the lift.
2. Dump pressure in the power supply system (Razdel Sbrasyvanie of pressure in the power supply system see).
3. Open лючок access and uncover a jellied mouth of a fuel tank.
4. Disconnect a negative wire from the battery.

5. Turn out fixing screws and remove a sealing flange.


6. Release nuts of fastening of the right back wheel, then lift the car over the earth and remove a wheel.
7. Merge fuel from the main chamber of a fuel tank (see the Head of the Power supply system and release).
8. Screw into place and tighten with demanded effort (26 Nanometers) a drain stopper.
9. Establish into place the panel of lateral protection of a tank and tighten bolts of its fastening with effort of 18 Nanometers.

10. Remove a protector of a jellied mouth.

11. Turn out bolts of arms of fastening испарительной tubes to a jellied mouth.

12. Turn out bolts of fastening of an arm of a jellied mouth to a body.


13. Release fixing collars and remove the main and ventilating hoses of a jellied mouth.
14. Remove a mouth.

INSTALLATION

 PERFORMANCE ORDER

1. Without closing лючок access, establish a fuel plate () with a rubber sealant () and fill a jellied mouth in a reception aperture from the interior of a wheel arch. Level a mouth, establish a cup () (see in the same place) and tighten fixing screws.

 At a bending of edges of a sealant inside straighten them by means of a screw-driver.

2. Plant the main hose on the bottom section of a tube of a jellied mouth (нахлест should make an order 35 ÷ 40 mm) and strongly fix its collar.

 Track, that collars did not concern a ventilating hose and a beam of a back suspension bracket!


3. Operating in a similar manner, establish a hose a ventilating hose (нахлест at landing of a hose to a tube should make 25 ÷ 30 mm).
4. Tighten bolts of fastening of a basic arm of a jellied mouth to a body with effort of 7.4 Nanometers.
5. Tighten fastening bolts испарительного a hose.
6. The further installation is made in an order, the return to an order of dismantle of components. Track, that elements of a jellied mouth did not adjoin to suspension bracket elements.


On the main page