Subaru Legacy/Outback

1999-2003 of release

Repair and car operation

Check of a condition and replacement of fuel lines and them штуцерных connections

The scheme of connection of fuel lines on models 2.0 and 2.5 l equipped with system OBD II

1 — the Thermoprotective cover
2 — Assembly tapes of fastening of a fuel tank
3 — the Left forward protective panel
4 — the Right forward protective panel
5 — the Fuel tank
6 — the Flange of fastening of assemblage of the fuel pump
7 — Pump assemblage
8 — the Gauge of a stock of fuel
9 — the Fuel filter
10 — the Fuel pump with the filter
11 — the Sealing lining of the valve отсечки fuel
12 — the Valve отсечки fuel
13 — the Hose And испарительной lines
14 — the Collar
15 — the Hose With испарительной lines
16 — the Connecting tube
17 — the Hose In испарительной lines
18 — the Hose And the pumping pump
19 — the Line of return of fuel
20 — the Clamp
21 — the Socket of fast joining
22 — the Hose In the pumping pump
23 — the Sealing lining of the gauge of level of fuel in the additional chamber of a tank

24 — the Filter of the pump of pumping
25 — the Gauge of level of fuel in the additional chamber
26 — the Left back protective panel
27 — the Right back protective panel
28 — the Hose of the fuel filter
29 — the Air ventilating hose
30 — Collars
31 — the Sealing lining
32 — the Cover
33 — the Sealing lining
34 — the Fixing flange of the valve отсечки fuel
35 — the Line of giving of fuel
36 — the Sealant
37 — Assembly скоба
38 — the Landing plug

Efforts of a tightening of carving connections, Nanometer

Т1: 4.4
Т2: 18
Т3: 33
Т4: 5.9

The scheme of connection of fuel lines on models 2.0 and 2.5 l equipped with system OBD Subaru

1 — Collars
2 — the Hose And lines of giving of fuel
3 — the Hose And испарительной lines
4 — Collars
5 — the Hose In a line of giving of fuel
6 — the Hose And lines of return of fuel
7 — the Drainage hose
8 — the Coal adsorber
9 — the Hose And a coal adsorber
10 — the Double-thread valve
11 — the Hose In a coal adsorber
12 — the Hose From a coal adsorber

13 — the Basic arm of a coal adsorber
14 — Lines of a fuel path
15 — the Hose In испарительной lines
16 — the Hose From a line of return of fuel
17 — the Hose From a line of giving of fuel
18 — the plug Through passage

Efforts of a tightening of carving connections, Nanometer

Т: 7.4 ± 2.0

The scheme of connection of fuel lines on l models 3.0 (OBD II)

1 — Collars
2 — the Hose And lines of return of fuel
3 — the Hose And lines of return of fuel
4 — Collars
5 — Lines of a fuel path
6 — the plug Through passage
7 — the Hose And испарительной lines
8 — the Hose And испарительной lines
9 — the Hose In a line of giving of fuel
10 — the Basic arm
11 — the Hose In испарительной lines
12 — the Hose of the double-thread valve
13 — the Double-thread valve
14 — the Basic arm of the double-thread valve

15 — the Drainage hose of the double-thread valve
16 — the Drainage hose
17 — Shtutsernyj a socket of a fuel path
18 — Lines испарительного a path
19 — the Hose of a purge of a coal adsorber
20 — the Hose With испарительной lines
21 — the Drainage hose of a coal adsorber
22 — the Coal adsorber

Efforts of a tightening of carving connections, Nanometer

Т1: 23
Т2: 33

PERFORMANCE ORDER

The prevention in pressure Razdela Sbrasyvanie beginning in the power supply system see.

1. Lines of a fuel path of the power supply system are laid between a petrol tank and an impellent compartment of the car. Steel tubes and flexible fuel hoses fasten to the bottom of the car by means of clips and screw fixture. Each time when the car rises over the earth with any purpose (for example, for survey or replacement of components of system of release of the fulfilled gases), try to take advantage of a case and to check up a condition of fuel lines and them штуцерных connections.
2. Attentively examine all hoses and tubes of a fuel path on presence of cracks, twisting, deformations and other mechanical damages.
3. At revealing of signs of internal pollution or passableness infringement corresponding section of a fuel path it is necessary to remove and blow compressed air.
4. Make sure of reliability of a tightening of all штуцерных connections of hoses and metal tubes of a fuel path.

Steel tubes

PERFORMANCE ORDER

1. Use as replaceable sections only high-strength steel tubes of manufacture of the manufacturers who have proved in the automobile market.
2. Remember that copper and aluminium tubes are not capable to sustain vibrating loadings arising while in service the car.
3. Do not forget that fuel lines on the models equipped with system of injection, should maintain high internal pressure.
4. Often in firm shops of automobile accessories it is possible to get equipped carving штуцерными nozzles of section of metal tubes. At easing and a tightening штуцерных connections use two wrenches to avoid проворачивания a reciprocal part of a socket. Without fail check a condition used for hermetic sealing штуцерных connections of sealing rings. The worn out or mechanically damaged rings at once replace. Try to use as replaceable components only firm details.

Flexible hoses

PERFORMANCE ORDER

At replacement of fuel hoses use only the firm components calculated on high internal pressure!

Flexible fuel hoses should be laid not more close than in 10 sm from components of system of release of the fulfilled gases and is not closer than in 25 sm from каталитического than the converter. Watch, that fuel lines did not adjoin with кузовными elements and suspension bracket components. The minimum admissible size of a backlash makes 6.3 mm.

Replacement

PERFORMANCE ORDER

1. The general scheme of a lining of fuel lines is shown on сопр. Illustrations.

2. Tyre out the car on the lift.
3. Dump pressure in the power supply system (Razdel Sbrasyvanie of pressure in the power supply system see).
4. Open лючок access to a jellied mouth of a fuel tank and uncover mouths.
5. Unbend a carpet covering.
6. Remove tubes and lines of lines of giving and fuel return, and also lines of fuel evaporations.
7. Make a detachment of fuel/isparitelnyh lines in an impellent compartment.

8. Lift аль on the lift.

9. Disconnect a hose () from the double-thread valve and a hose () from a tube испарительной to a line – it should be distributed two distinct clicks.

10. Wipe and disunite sockets of fast joining of lines of giving and fuel return: Keeping a socket (), wring out downwards a clamp (), then, having pulled, liberate a tube () with the clamp put on it from the socket case. Remove a clamp and wipe the sealing end of a tube (D). Check up a condition of components, in case of need make replacement.

And — the Socket
In — the Clamp
With — the Tube
D — the Sealing surface

11. Installation is made upside-down. Pay attention to the moments listed more low.

12. At connection of fuel tubes fill the NEW clamp () in a socket of fast joining (), then against the stop push in assemblage a tube of a fuel line, - track, that both uvulas of a clamp have got to reception nests of a socket. Having pulled for tubes, make sure of reliability of a joint.

13. Generally at connection to fuel tubes of hoses нахлест should make not less than 20 ч 25 mm.

1 — Shtutsernoe the tube termination
2 — the Collar
3 — the Hose
l: 2.5 ± 1.5 mm
L: 22.5 ± 2.5 mm

14. The fixing scheme on the unions of hoses испарительных lines is shown on an illustration.

1 — the Hose
2 — the Collar
3 — Shtutsernoe the tube termination
L: 27.5 ± 2.5 mm

Repair

PERFORMANCE ORDER

In case of damage of a metal or flexible fuel line it is necessary to replace the failed section only with a firm replaceable element of a corresponding standard size.

On the main page