Subaru Legacy/Outback

1. Dump pressure in the power supply system (Razdel Sbrasyvanie of pressure in the power supply system see).
2. Open лючок access and uncover a jellied mouth of a fuel tank.
3. Disconnect a negative wire from the battery.

1. Remove inlet section of an air path with an air cleaner and воздухоприемной the chamber (see Has undressed Service of components of an inlet air path).
2. Disconnect cables of a drive throttle заслонки.
3. Remove assemblage of the steering pump (electroconducting disconnect) and, without disconnecting from it hydraulic lines, postpone for a mudguard of the right wing, preliminary having spread rags.

4. Turn out bolts of fastening of the tank of a liquid of washing of glasses.

5. Disconnect electroconducting from electromotors of pumps of giving of a liquid on the forward and back has flown down.

6. Disconnect a hose from the pump of giving of a liquid on back glass, - the open end of the union at once закупорьте.

7. Remove the tank and tie up it to the left loop of a cowl.

8. Disconnect from a cover of a head of cylinders hoses PCV.

9. Disconnect hoses охладительного a path from the throttle case.

10. Disconnect a hose of the vacuum amplifier of brakes.

11. Lift the receiver also valve EGR, - try not to drop sealing linings.

12. Disunite sockets of connection of electroconducting of the engine to laid on a partition of a motor compartment to a plait.

13. Disconnect from the inlet pipeline the tyre of grounding of the power unit.

14. Disconnect from tubes hoses of fuel lines, - in avoidance разбрызгивания fuel turn released штуцерные sockets rags.
15. Disconnect the tyre of grounding from a protector of the left fuel highway, then remove a protector.

16. Disconnect a hose of giving of additional air (), then turn out bolts () fastenings of the left fuel highway to a head of cylinders.

17. Disconnect the tyre of grounding and remove a protector of the right fuel highway.

18. Disconnect a hose of giving of additional air (), then turn out bolts () fastenings of the right fuel highway to a head of cylinders.

19. Turn out fixing bolts to heads of cylinders and remove assemblage of the inlet pipeline.

6. Cнимите assemblage of the case of a throttle.

7. Disconnect electroconducting from the valve подмешивания air to injectors. Turn out fixing bolts and remove assemblage of the valve from the inlet pipeline.

8. Disconnect from the pipeline a vacuum hose of a regulator of pressure.

9. If have not done it at a dismantle stage, remove protectors of fuel highways.

10. Disconnect electroconducting from fuel injectors and the electromagnetic valve of a purge of a coal adsorber.

11. Disconnect перепускной a hose from the electromagnetic valve of a purge of an adsorber.

12. Remove collars () and basic arms () fastenings on the inlet pipeline of a plait of electroconducting of the engine. Remove burn down electroconductings.

13. Turn out a fixing bolt and remove the electromagnetic valve of a purge of a coal adsorber.

14. Turn out fastening bolts to the inlet pipeline of fuel tubes.

15. Take clamps and remove fuel injectors.

16. Disconnect from the inlet pipeline перепускные air hoses.

17. Release fixing collars of fuel hoses and remove assemblages of fuel highways.

18. Turn out a fixing bolt and remove from the inlet pipeline assemblage of fuel lines and a regulator of pressure of fuel.

4. Having disconnected electroconducting, remove the electromagnetic valve of management of a purge of a coal adsorber and valve EGR.

5. Having released fixture, remove from the inlet pipeline burn down engine electroconductings.

6. Remove from the inlet pipeline tube PCV.

7. Remove assemblage of tubes подмешивания air to injectors and purges of a coal adsorber.

8. Disconnect from the inlet pipeline a vacuum hose () a pressure regulator, then turn out fixing bolts and remove assemblage of a fuel highway.

9. Disconnect from the inlet pipeline a vacuum hose.

2. Track, that all fixture has been tightened with demanded effort (Specifications and signatures to illustrations in subsection "Dismantling" see).

1. Assemblage is made in an order, the return to an order of dismantle of components. Track correctness of connection испарительных hoses to the electromagnetic valve of management of a purge of a coal adsorber and vacuum hoses of the induction valve.
And — To a purge line
In — To a fuel line

2. Track, that all fixture has been tightened with demanded effort (Specifications and signatures to illustrations in subsection "Dismantling" see).

Installation is made in an order, the return to an order of dismantle of components. Track, that all fixture has been tightened with demanded effort (Specifications and signatures to accompanying illustrations in subsection "Removal" see). Do not forget to establish to the place of the relay of the fuel pump (Razdel Sbrasyvanie of pressure in the power supply system see).