Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
- The power supply system and release
   Specifications
   - System of injection of fuel
      Sbrasyvanie pressure in the power supply system
      Опорожнение a fuel tank
      Check of a condition and replacement of fuel lines and them штуцерных connections
      Service of components of an inlet air path
      Removal and installation of the case of a throttle
      Service of components of a drive throttle заслонки
      Removal, service and installation of the inlet pipeline
      Service of the fuel pump
      Removal and installation of main relay MFI
      Removal and installation of the relay of the fuel pump
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of the gauge of level of fuel in the additional chamber of a fuel tank
      Removal, check and installation of the fuel filter
      Removal and installation запорного the valve отсечки fuel
      Removal and installation демпфирующих fuel valves
      Removal and installation of a fuel tank
      Removal and installation of a jellied mouth of a fuel tank
      Removal and installation of components of system of injection of fuel
   + Control systems of the engine and decrease in toxicity of the fulfilled gases
   + System of release of the fulfilled gases
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of the case of a throttle

Details of installation of the case of a throttle of the 4-cylinder engine

1 — the Sealing lining
2 — the Gauge of position throttle заслонки (TPS)
3 — the Electromagnetic valve of stabilisation of turns of idling (IAC)
4 — the throttle Case

Efforts of a tightening of carving connections, Nanometer

Т1: 1.6
Т2: 22


Details of installation of the case of a throttle of the 6-cylinder engine

1 — the Sealing lining
2 — the pressure Gauge in the inlet pipeline (MAP)
3 — Electromagnetic valve IAC
4 — TPS
5 — the Sealing ring
6 — the throttle Case

Efforts of a tightening of carving connections, Nanometer

Т1: 1.6
Т2: 2.8
Т3: 22

Models 2.0 and 2.5 l

 PERFORMANCE ORDER

1. Details of installation of the case of a throttle of the 4-cylinder engine are shown on an illustration.
2. Disconnect a negative wire from the battery.
3. Remove assemblage воздухоочистите ля (see Has undressed Service of components of an inlet air path).


4. Disconnect cables of a drive throttle заслонки () and ().

And — a gas Cable
In — the Cable темпостата

5. Disconnect electroconducting from the electromagnetic valve of system of stabilisation of turns of idling (IAC) and the gauge of position throttle заслонки (TPS).

AND — TPS
In — Electromagnetic valve IAC
With — Perepusknoj an air hose

6. Disconnect перепускной an air hose from the valve подмешивания secondary air to injectors.

7. Disconnect from the case of a throttle hoses охладительного a path.

8. Turn out bolts of fastening of the case of a throttle to the inlet pipeline.
9. Installation is made upside-down. Do not forget to replace all sealing elements. Bolts of fastening of the case of a throttle tighten with effort of 22 Nanometers.

L models 3.0

 PERFORMANCE ORDER

1. Details of installation of the case of a throttle are presented on an illustration.
2. Disconnect a negative wire from the battery.
3. Remove воздухоприемную the chamber (see Has undressed Service of components of an inlet air path).

4. Disconnect cables of a drive throttle заслонки () and ().

And — a gas Cable
In — the Cable темпостата

5. Disconnect electroconducting from the electromagnetic valve of system of stabilisation of turns of idling (IAC) and the pressure gauge in the inlet pipeline (MAP).

And — Gauge MAP
In — Electromagnetic valve IAC
With — Perepusknoj an air hose

6. Disconnect from valve IAC перепускной an air hose.

7. Disconnect electroconducting from the gauge of position throttle заслонки (TPS).

8. Disconnect from the case of a throttle hoses охладительного a path.

9. Turn out bolts of fastening of the case of a throttle to the inlet pipeline.
10. Installation is made upside-down. Do not forget to replace all sealing elements. Bolts of fastening of the case of a throttle tighten with effort of 22 Nanometers.

On the main page