Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
- Onboard electric equipment
   Search of causes of failures of an electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting and alarm devices
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation прикуривателя
   Alarm system “do not forget to switch off lighting devices” - the general information
   Removal and installation of a small horn of a horn
   Removal and installation drive a cable of a speedometer/gauge of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of the electromotor and draughts of a drive of a cleaner of a windscreen
   Removal and installation of the electromotor of a drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system - the general information
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of a pillow of safety
   Diagnostics of systems of electronic control
+ Electric equipment schemes

Removal and installation of components of a pillow of safety

The safety measures resulted in the previous section see.

The general information

Gauges of a pillow of safety are built in the electronic block of management (ECU) the systems, which built in in a car steering wheel. The control lamp is built in assemblage of a pillow of safety.

In case of occurrence of any doubts in serviceability of functioning of system, immediately address for consultation to experts of car-care centre. At all do not undertake independent attempts of carrying out of diagnostics of a condition of system, or service of its components, besides described below procedures of removal and installation of the module of a pillow of safety or its rotating drum-type socket.

The electronic block of management (ECU) safety pillows

The block is built in a steering wheel and in an individual order is not delivered. The description of procedures of removal and steering wheel installation is resulted in the Head "the Running gear and a steering".

The module of a pillow of safety

Removal

The module of a pillow of safety is built in in the central part of a steering wheel.

 PERFORMANCE ORDER

1. Make system deactivation (the safety Pillow - the general information see, safety measures and system deactivation).
2. Turn a steering wheel so that to provide access to two screws of fastening of the module of a pillow of safety. Screws are located from the back party of assemblage of a steering wheel.

3. Turn out two fixing screws.

4. Liberate one of edges of the module of a pillow of safety of the central part of a steering wheel, then develop the module the released edge outside, completely without removing it.

5. Cautiously disunite an orange contact socket of electroconducting of system, then definitively take the module from steering wheel assemblage.

6. If the module acts in film from the car for a long time, accept corresponding safety measures on its storage (the safety Pillow - the general information see, safety measures and system deactivation).

Installation

Installation is made upside-down. Pay attention to following moments:
   a) Try not to drop and not to shake the established module of a pillow of safety;
   b) Having finished module installation, make system activation (the safety Pillow - the general information see, safety measures and system deactivation).

Rotating drum-type socket of a pillow of safety

Removal

 PERFORMANCE ORDER

1. Remove the module of a pillow of safety (see above).
2. Remove a steering wheel (address to the Head the Body and salon furnish).
3. Remove casings of a steering column (address to the Head the Body and salon furnish).

4. Find on the right under a steering column two tips of electroconducting of a drum-type socket and disunite them.
1 Shtekernye sockets of electroconducting of a radio tape recorder
2 Shtekernye sockets of a pillow of safety

5. By means of a small screw-driver release a fixing clamp.

6. Remove rotating drum-type socket from a steering column.

7. Liberate electroconducting from a casing (in case of need remove assemblage подрулевого the switch).

Installation

Installation is made upside-down.


On the main page