Citroen Xantia

1. Remove a steering wheel (address to the Head the Running gear and a steering).
2. Remove casings of a steering column (address to the Head the Body and salon furnish).

3. Turn out two screws of fastening подрулевого the switch.

4. Disunite a contact socket () in a back part of the switch and take assemblage from a casing.

5. Installation is made upside-down. The description of procedure of installation of a steering wheel is resulted in the Head the Running gear and a steering.

1. Remove the central overlay of a steering wheel, at a corresponding complete set remove the module of a pillow of safety (Removal and installation of components of a pillow of safety see).

2. Turn out two opened fixing screws and take assemblage of switches from a steering wheel.

3. Disconnect from switches electroconducting and remove assemblage.

4. Installation is made upside-down. The description of procedure of installation of the module of a pillow of safety is resulted in section Removal and installation of components of a pillow of safety.

1. Accurately having hooked, liberate from the panel of devices an ashtray, then turn out two fixing screws in the bottom part of facing of control panels heater and radio tape recorder functioning and, hooking a small screw-driver, remove facing.

2. On models with the central arrangement of a radio tape recorder on the panel of devices turn out two fixing screws and take assemblage of a radio tape recorder from the landing nest, disconnect from a back part of assemblage electroconducting and an antenna cable.

3. Turn out four screws and take from the panel of devices a radio tape recorder casing. In case of need liberate from clamps on a casing electroconducting and an antenna cable.

4. On the models equipped with the central ware shelf in the panel of devices, turn out four fixing screws and remove a shelf.
5. Through an aperture under radio tape recorder installation reach clamps of fastening of switches.
6. Release clamps and push out switches from the panel of devices (outside).
7. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets of electroconducting.

1. Remove casings of a steering column (address to the Head the Body and salon furnish).
2. Open a cover of the assembly block of safety locks for the purpose of providing of access to the bottom party of angular finishing section of the panel of devices from the driver's party of the car.

3. Turn out the top and bottom screws of fastening of angular section, delay furnish on itself and disconnect from it (or from switches) electroconducting. Try to remember adjusting position of contact sockets. Remove finishing section.

4. In a back part of finishing section release clamps of fastening of switches and push out them from the panel outside.
5. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets.

1. Operate, as it is described in subsection "the Bottom switches established from the driver's party of the panel of devices", subitem 1-3.
2. Release clamps from the back party of finishing section and push out switches from the panel outside.
3. Installation is made upside-down. Track correctness of connection and reliability of fastening of contact sockets.

1. Liberate a small ware box / the finishing panel of switches from the central console of the car.

2. Take from the console the panel of switches and disconnect from it electroconducting.

3. Push out switches from the panel outside.
4. Installation is made upside-down.

1. Turn out the screw located from below on back edge of the panel of facing of the door handle.

2. Accurately having hooked, remove facing of the handle and disconnect the electroconducting brought to assemblage of switches.

3. Take the metal clamp located from the back party of a basic plate and remove assemblage of switches.

4. Release clamps and push out switches from assemblage outside.

5. Installation is made upside-down. For fastening of a basic plate of assemblage of switches take advantage of a new metal clamp.

1. Execute the procedures described in subsection "Switches of management of electric drive functioning Glass lifts", subitem 1-2.
2. Now it is necessary will separate the basic panel of the switch from facing of the internal handle of a door.
3. Two panels are connected by plastic clamps which can be broken off or drilled.
4. After division of basic panels push out the switch from assemblage outside.
5. Installation is made upside-down. For fastening of panels take advantage of new clamps.

1. Open a door and remove from the door switch a rubber protective cover.
2. Turn out the switch and liberate it from a rack. Disconnect the electroconducting brought to the switch and remove assemblage from the car.

Glue electroconducting by an adhesive tape, without allowing to fail thereby to it in a rack.

3. Installation is made upside-down. Track reliability of landing on the switch of a protective cover.

1. Open a cover of a ware box, then release a lock uvula in a back part of a cover and completely lower last.

2. Having hooked, liberate the switch of illumination of a box and disconnect from it electroconducting.

3. Installation is made upside-down.

1. Open a back door, turn out fixing screws, release clamps and remove the panel of an internal upholstery.

2. Turn out screws of fastening of the gauge-switch to a door, remove a lock washer.

3. Disconnect electroconducting and remove the gauge-switch.
4. Installation is made upside-down. Track connection to the gauge-switch of a wire of grounding.

1. Remove the central console (address to the Head the Body and salon furnish).

2. Having hooked, liberate the gauge-switch from a basic arm in a back part of a control lever of a lay brake, disconnect electroconducting.

3. Installation is made upside-down.

1. Having hooked, liberate a rheostat from the bottom casing of a steering column, disconnect electroconducting.
2. Connect electroconducting and latch a rheostat back in a casing.

1. Remove a steering wheel (address to the Head the Running gear and a steering).
2. Remove casings of a steering column (address to the Head the Body and salon furnish).
3. Walk on electroconducting back from the switch and disunite its contact socket.
4. Turn out fixing screws and remove assemblage of the switch from a steering column.
5. Installation is made upside-down.