Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
- Onboard electric equipment
   Search of causes of failures of an electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting and alarm devices
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation прикуривателя
   Alarm system “do not forget to switch off lighting devices” - the general information
   Removal and installation of a small horn of a horn
   Removal and installation drive a cable of a speedometer/gauge of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of the electromotor and draughts of a drive of a cleaner of a windscreen
   Removal and installation of the electromotor of a drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system - the general information
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of a pillow of safety
   Diagnostics of systems of electronic control
+ Electric equipment schemes

Removal and installation of external lighting and alarm devices

Before to start removal of lighting devices, do not forget to disconnect a negative wire from the battery.

Head block headlights

Removal

 PERFORMANCE ORDER

1. Remove the forward index of turn from a corresponding board of the car (see more low) and a forward lattice (address to the Head the Body and salon furnish).
2. Turn out two top fixing screws and one bottom.

3. Remove assemblage of a block headlight from the car (the top bolts are shown by arrows).



4. Disconnect the electroconducting brought to assemblage.

5. In case of need the lens can be removed from a headlight:
   a) Accurately hooking a screw-driver, release clamps of fastening of edges of a lens. At assemblage clamps are subject to replacement without fail;

   b) Cautiously remove a lens from a block headlight. Try not to touch with fingers a surface of a mirror of a reflector;
   c) Remove and will throw out a sealing lining;
   d) Clean an adjusting flute in a casing of a block headlight and plant in it a new sealing lining;

   e) Plant on ledges along the edges of a lens new fixing clamps, then press a lens to a casing of assemblage of a block headlight and in strictly certain order latch clamps.

Installation

Installation is made upside-down. At the first possibility make check / updating of installation of optical axes of block headlights.

Forward indexes of turns

Removal

 PERFORMANCE ORDER

1. Open a cowl.

2. From the interior of a wing release a fixing clamp and push out outside assemblage of the index of turn (an arrow the fixing clamp is shown).



3. Disconnect electroconducting and remove assemblage of the index from the car.

Installation

Installation is made upside-down. Track reliability защелкивания a clamp.

Lateral repeaters of forward indexes of turn

Removal

 PERFORMANCE ORDER

1. Shift repeater assemblage forward and liberate it from кузовной car panels.
2. Disconnect electroconducting and remove repeater assemblage.

Installation

Installation is made upside-down.

Forward antifog headlights

Removal

 PERFORMANCE ORDER

1. Pull facing of assemblage of an antifog headlight forward before the click confirming отпускание of clamps.

2. Push a screw-driver in the top corner of a ventilating aperture in a spoiler and wring out a clamp of fastening of assemblage of an antifog headlight.

3. Having pulled on itself, liberate assemblage of an antifog headlight from the landing nest (an arrow the fixing clamp is shown).

4. Disconnect it from a spoiler (an arrow the lock uvula is shown).

5. Disconnect electroconducting and remove assemblage of an antifog headlight from the car.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down. Before to fill assemblage in a spoiler, make sure that its facing is shifted in the forward (released) position. First of all fill in a spoiler the lock uvula located from external edge of a headlight.
2. Having planted assemblage заподлицо with a spoiler surface, fix its clamp.

Adjustment

Adjustment of an optical axis of an antifog headlight is made by means of the special screw located from the interior of assemblage. The screw turns a screw-driver with a crosswise sting which should be passed in the central groove in a spoiler.

Built in at a back door the back combined lanterns

Removal

 PERFORMANCE ORDER

1. Open a back door.
2. Release a clamp and remove a folding cover from the back party of lantern assemblage.
3. Disconnect electroconducting from a back part ламподержателя, then release two fixing clamps and remove ламподержатель.

4. Having hooked a screw-driver, release an internal clamp.

5. Then pull lantern assemblage outside and release two remained external clamps.

Installation

Installation is made upside-down.

The back combined lanterns built in in wings

Removal

 PERFORMANCE ORDER

1. In a car luggage space give a fixing nut and remove from a wing assemblage of the back combined lantern.

Installation

Installation is made upside-down.

Lanterns of illumination of licence plate

Removal

 PERFORMANCE ORDER

1. Accurately having hooked a screw-driver, liberate assemblage of a lantern of illumination of licence plate from the panel of a door of a back.
2. Disconnect electroconducting and remove assemblage of a lantern from the car.

Installation

Installation is made upside-down.


On the main page