Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
- Onboard electric equipment
   Search of causes of failures of an electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting and alarm devices
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation прикуривателя
   Alarm system “do not forget to switch off lighting devices” - the general information
   Removal and installation of a small horn of a horn
   Removal and installation drive a cable of a speedometer/gauge of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of the electromotor and draughts of a drive of a cleaner of a windscreen
   Removal and installation of the electromotor of a drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system - the general information
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of a pillow of safety
   Diagnostics of systems of electronic control
+ Electric equipment schemes

Replacement of lamps of internal lighting devices

The general information

Replacement of lamps of external lighting and alarm devices, subsection "General information" see.

Salonnye fixtures, mate lamps and illumination of an impellent compartment

 PERFORMANCE ORDER

1. Having hooked a screw-driver, liberate the fixture from a casing for the purpose of providing of access to a lamp.

2. Turn a cartridge counter-clockwise and take it together with a lamp.

3. The lamp has press landing in a cartridge.
4. Installation is made upside-down.

Illumination of a ware box

 PERFORMANCE ORDER

1. Open a cover of a ware box, release lock and a uvula and completely cast away a cover.

2. Having hooked, liberate the fixture from the top plane of a ware box.

3. Turn a cartridge counter-clockwise and take it from the fixture together with a lamp.

4. The lamp has press landing in a cartridge.

5. Replace a lamp and establish into place the fixture.

Lamps of illumination of switches

Illumination lamps are built in assemblages of switches and in an individual order are not delivered.

Lamps of illumination of the control panel heater functioning

 PERFORMANCE ORDER

1. Extend from the panel of devices an ashtray.
2. Turn out two fixing screws, then, hooking a small screw-driver, accurately release clamps and remove facing of control panels by radio tape recorder and heater functioning.
3. On the models equipped with a ware shelf in the central part of the panel of devices, turn out four fixing screws and remove a shelf.
4. Turn out two fixing screws and take from the panel of devices radio tape recorder assemblage. Disconnect from a back part of assemblage electroconducting and an antenna cable.
5. Turn out four fixing screws and liberate from the panel of devices a radio tape recorder casing. Where it is required, liberate from clamps on a casing electroconducting and an antenna cable.
6. Uncover assemblage of the control panel by heater functioning.

7. Liberate the holder of lamps of illumination from a back part of the panel.

8. Lamps have press landing in the holder.
9. Replace the failed lamp and establish components on the regular places. Operate in an order, the return to a dismantle order.

Lamp of illumination of hours

 PERFORMANCE ORDER

1. Take from the panel of devices assemblage of the central ventilating nozzle for the purpose of providing of access to hours (Removal and installation of hours see).

2. In a back part of hours turn a lamp cartridge counter-clockwise and take it from assemblage.

3. The lamp is built in a cartridge.
4. Replace a lamp and establish components into place.

Lamp of illumination of a prikurivatelja/ashtray

 PERFORMANCE ORDER

1. Extend an ashtray from the panel of devices.
2. Turn out two bottom fixing screws and completely remove assemblage of an ashtray from the panel of devices.
3. Having pulled outside, liberate a cartridge of a lamp from a back part of assemblage of an ashtray, disconnect electroconducting.
4. The lamp has press landing in a cartridge.
5. Replace a lamp and establish into place components. Operate in an order, the return to a dismantle order.

Control lamps and lamps of illumination of an instrument guard

 PERFORMANCE ORDER

1. Remove an instrument guard (Removal and installation of an instrument guard see).

2. Turn a lamp cartridge counter-clockwise and take it from a back part of a guard.

3. All lamps are built in the cartridges and replaced in gathering with it.
4. Replace the failed assemblage and establish components on the regular places. Operate in an order, the return to a dismantle order.



On the main page