Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
- Onboard electric equipment
   Search of causes of failures of an electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting and alarm devices
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and installation прикуривателя
   Alarm system “do not forget to switch off lighting devices” - the general information
   Removal and installation of a small horn of a horn
   Removal and installation drive a cable of a speedometer/gauge of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of the electromotor and draughts of a drive of a cleaner of a windscreen
   Removal and installation of the electromotor of a drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system - the general information
   Safety pillow - the general information, safety measures and system deactivation
   Removal and installation of components of a pillow of safety
   Diagnostics of systems of electronic control
+ Electric equipment schemes

Replacement of lamps of external lighting and alarm devices

The general information

At replacement of lamps do not forget following elementary rules:
   a) Before to start to work necessarily disconnect a negative wire from the battery;
   b) Remember that just the lamp flask remains hot during even some time after switching-off of last;
   c) Without fail check a condition of both contacts of a cartridge of the llama. In case of need smooth out contacts, having removed from them oxidation traces;
   d) At installation of lamps with a socle байонетного type (Specifications see) watch reliability of electric contact клеммных connections;
   e) Watch, that replaceable lamps on consumption rated power corresponded failed (especially at replacement of lamps of head or antifog headlights).

Head headlights

In head headlights two lamps access to which is possible from the back party of assemblage are used. The external lamp (located more close to a car wing) provides near illumination, internal - distant. Replacement of both lamps is made in an identical manner.

 PERFORMANCE ORDER

1. Open a cowl.

2. Release a clamp and uncover the back party of a block headlight.

3. Disconnect electroconducting from a back part of a cartridge to subject replacement of a lamp (a wire of red colour). Compress lock uvulas and release a spring clamp of fastening of assemblage of a lamp with a cartridge in a back part of a block headlight.
Above — the Contact socket of electroconducting and a spring clamp of fastening of a cartridge of a lamp of a headlight
Below — the Contact socket of electroconducting and a spring clamp of fastening of a cartridge of a lamp of a passing light
1 and 2 lock uvulas of a spring clamp



4. Take assemblage of a lamp with a cartridge from a block headlight.

5. Try not to touch a flask of a new lamp barehanded, - use a napkin or pure rags. Left fingers on glass fatty stains lead to decrease in intensity of illumination and reduction of service life of a lamp. Casually left traces remove the rags impregnated with methyl spirit.
6. Establish assemblage of a new lamp. Track correctness of hit of lock uvulas in grooves of cartridge assemblage. Fix assemblage by a spring clamp and connect to it electroconducting.
7. Establish into place a plastic back cover of a block headlight, having tracked correctness of its landing.

Forward dimensional fires

 PERFORMANCE ORDER

1. Open a cowl.
2. Release a clamp and uncover the back party of a head block headlight.
3. The lamp of dimensional fire is located between two lamps of head illumination.

4. Turn a lamp cartridge on a turn quarter counter-clockwise and take assemblage of a lamp with a cartridge from a block headlight.

5. The lamp has press landing in a cartridge.
6. Replace a lamp and establish cartridge assemblage in a block headlight. Operate in an order, the return to a dismantle order.

Forward indexes of turns

 PERFORMANCE ORDER

1. Open a cowl.

2. From the interior of a wing release a fixing clamp and push out assemblage of the index of turn from a wing forward (an arrow the fixing clamp is shown).



3. Turn cartridge assemblage counter-clockwise and take it from index assemblage.

4. The lamp is equipped by a socle байонетного type.
5. Replace a lamp and establish cartridge assemblage and the index on the regular places. Operate in an order, the return to a dismantle order.

Lateral repeaters of forward indexes of turn

 PERFORMANCE ORDER

1. Shift repeater assemblage forward and liberate it from кузовной panels.

2. Turn cartridge assemblage counter-clockwise and liberate it from repeater assemblage.

3. The lamp has press landing in a cartridge.
4. Replace a lamp and establish the repeater on the regular place. Operate in an order, the return to a dismantle order.

Forward antifog headlights

 PERFORMANCE ORDER

1. Remove a headlight (Removal and installation of external lighting and alarm devices see).
2. Turn a back cover of a headlight on a turn quarter counter-clockwise and remove it.

3. Disconnect electroconducting of a lamp from contact on a cover.

4. Wring out lock uvulas and release a spring clamp of fastening of cartridge assemblage in a back part of a headlight.

5. Take a cartridge with a lamp.

6. Try not to touch a flask of a new lamp barehanded, - use a napkin or pure rags. Left fingers on glass fatty stains lead to decrease in intensity of illumination and reduction of service life of a lamp. Casually left traces remove the rags impregnated with methyl spirit.
7. Establish assemblage of a new lamp. Track correctness of hit of lock uvulas in grooves of cartridge assemblage. Fix assemblage by a spring clamp and connect to it electroconducting.
8. Establish into place a plastic back cover of a headlight, having tracked correctness of its landing.
9. Establish headlight assemblage on the regular place (Removal and installation of external lighting and alarm devices see).

Established on a back door the combined lanterns

 PERFORMANCE ORDER

1. Open a back door.

2. Release a clamp and open a back folding cover of lantern assemblage.

3. Wring out two lock uvulas and take from a lantern assemblage ламподержателя.
Above fastening Clamps ламподержателя
Below Removal ламподержателя the back combined lantern from a back door



4. In a lantern lamps with socles байонетного type are used.
5. Replace the failed lamps and collect a lantern. Operate in an order, the return to a dismantle order.

The back combined lanterns established on wings

 PERFORMANCE ORDER

1. In a luggage space give a fixing nut () and liberate from a wing assemblage of the combined lantern.
Above Fixture of a cover of the back combined lantern (Хэтчбэк)
Below Fixture of a cover of the back combined lantern (Versatile person)



2. Wring out lock uvulas and take from lantern assemblage ламподержатель.

3. In a lantern lamps with socles байонетного type are used.
4. Replace the failed lamps and collect a lantern. Operate in an order, the return to a dismantle order.

Lanterns of illumination of licence plate

 PERFORMANCE ORDER

1. Having hooked a small screw-driver, remove a lens from lantern assemblage.

2. The lamp has press landing in a cartridge.

3. Replace a lamp and establish into place a lens.

Top level Stoplight

 PERFORMANCE ORDER

1. The Stoplight is built in at a door of a back of the car.

2. Open a back door.

3. For the purpose of providing of access to ламподержателю, give two fixing nuts.



On the main page