Opel Kadett E

1984-1991 of release

Repair and car operation


Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   - 4.1. Engine OHV (with a camshaft in the block of cylinders)
      4.1.1. A technical characteristics
      4.1.2. Compression check
      4.1.3. The repair operations which are not demanding removal of the engine
      + 4.1.4. The repair operations demanding removal of the engine
      4.1.5. Adjustment of backlashes of valves
      + 4.1.6. A head of the block of cylinders
      4.1.7. Removal and installation of the oil pallet
      + 4.1.8. The oil pump
      - 4.1.9. Mechanism asterisks timing
         4.1.9.1. Removal of asterisks
         4.1.9.2. Installation of asterisks
      + 4.1.10. Pistons and rods
      4.1.11. Removal and flywheel installation
      4.1.12. Removal and installation of support of the power unit
      4.1.13. Removal and installation of a camshaft and pushers
      4.1.14. Removal and installation of a back sealing ring of a cranked shaft
      4.1.15. Removal and installation of a cranked shaft and radical bearings
      + 4.1.16. Check of elements of the engine
      4.1.17. System of greasing of the engine
      4.1.18. Removal and engine installation
      4.1.19. Start of the engine after major repairs
   + 4.2. Engines OHC
   + 4.3. Engine DOHC with 16 valves
   + 4.4. Diesel engines 16D and 16DА
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

4.1.9.2. Installation of asterisks
PERFORMANCE ORDER
1. For replacement of a sealing ring in a cover establish a cover on two бруска and, using a hammer and выколотку, beat out an old sealing ring together with the holder.
2. Lower a new sealing ring in pure engine oil at 24 o'clock. Establish a new sealing ring in the holder.
3. Establish the holder in a drive cover so that the holder was established заподлицо with a cover.
4. Establish an asterisk on a cranked shaft.
5. Establish a camshaft asterisk in приводную a chain so that at asterisk installation on a label camshaft on asterisks have been directed to each other.
6. Establish an asterisk on a camshaft and fix a bolt with a washer, having tightened a bolt the demanded moment. Keep an asterisk from проворачивания in the same way, as well as at bolt unscrewing.
7. Establish the tension mechanism приводной chains. If the mechanism with oil giving under pressure is used, manually compress колодку axial pressure both fix the mechanism and release колодку.
8. At installation of the mechanism of a tension with a spring establish the tension mechanism into place and fix the bottom bolt. A screw-driver move a spring from the case of the mechanism of a tension and screw in the top bolt of fastening of the mechanism of a tension.
9. Release a spring and tighten bolts of fastening of the mechanism of a tension the demanded moment.
10. Establish an oil reflector on a cranked shaft and a new lining of a cover of a drive. Before installation put on both parties of a lining a thin layer of hermetic.
11. Establish a cover of a drive and screw in bolts of fastening of a cover on two or three turns. Establish a pulley of a cranked shaft to align a cover, and in diagonal sequence tighten bolts of fastening by the demanded moment.
12. Screw in a bolt of fastening of a pulley and tighten its demanded moment.
13. Establish auxiliary приводной a belt and adjust its tension.
14. Establish a wheel and lower the car on the earth. Tighten bolts of fastening of a wheel.


On the main page