Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
+ 4.1. Engine OHV (with a camshaft in the block of cylinders)
- 4.2. Engines OHC
4.2.1. A technical characteristics
4.2.2. Compression check
+ 4.2.3. The repair operations demanding removal of the engine
4.2.4. Removal and installation of auxiliary elements of the engine
4.2.5. Removal and installation of the valve of adjustment of pressure of oil
+ 4.2.6. A gear belt
+ 4.2.7. A head of the block of cylinders
4.2.8. Removal and camshaft installation
4.2.9. Removal and installation of the oil pallet
+ 4.2.10. The oil pump
4.2.11. Removal and installation of pistons and rods
4.2.12. Removal and flywheel installation
4.2.13. Removal and installation of a forward sealing ring of a cranked shaft
4.2.14. Removal and installation of support of the power unit
4.2.15. Replacement of a back sealing ring of a cranked shaft
+ 4.2.16. A cranked shaft and radical bearings
4.2.17. Check of details of the engine
4.2.18. System of greasing and ventilation system картера
4.2.19. Removal and engine installation
4.2.20. Start of the engine after major repairs
+ 4.3. Engine DOHC with 16 valves
+ 4.4. Diesel engines 16D and 16DА
+ 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes
|
Look the corresponding description in subsection 4.1.16.1, subsection 4.1.16.2, subsection 4.1.16.3, subsection 4.1.16.4, subsection 4.1.16.5, subsection 4.1.16.6, subsection 4.1.16.7 taking into account the following additional information.
CAMSHAFT
| PERFORMANCE ORDER |
| 1. Remove a camshaft and check up a condition of bearings of a camshaft on presence of deterioration and dot corrosion. In the presence of defects replace the camshaft case. |
| 2. Check up a camshaft condition on presence of scratches or development on surfaces of necks and cams. In the presence of defects replace a camshaft. Use of a camshaft with the increased diameter of necks of bearings is possible. In this case the camshaft is marked by a violet label. |
| 3. The plate of fixing of a camshaft should not have deterioration. Check up axial люфт a camshaft and if necessary replace a plate of fixing of a camshaft. |
| 4. At engine major repairs it is necessary to replace a forward sealing ring of a camshaft necessarily. |
|
GEAR BELT
| PERFORMANCE ORDER |
| 1. Check up a gear belt on presence of stratifications, cracks or deformation of teeths. In the presence of any defects replace a gear belt. |
| 2. Replacement of a gear belt is necessary for making through 50 000 km of run irrespective of its condition. |
| 3. If the gear belt is repeatedly established, before its removal note a direction of its rotation. |
|
HYDRAULIC PUSHERS
In the presence of deterioration or defects in a hydraulic pusher it is necessary to replace it in gathering.
PISTON MARKS
Number or code of pistons is located about consolidation of the oil pallet or about engine number. |
On the main page
|