Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   + 4.1. Engine OHV (with a camshaft in the block of cylinders)
   - 4.2. Engines OHC
      4.2.1. A technical characteristics
      4.2.2. Compression check
      + 4.2.3. The repair operations demanding removal of the engine
      4.2.4. Removal and installation of auxiliary elements of the engine
      4.2.5. Removal and installation of the valve of adjustment of pressure of oil
      + 4.2.6. A gear belt
      + 4.2.7. A head of the block of cylinders
      4.2.8. Removal and camshaft installation
      4.2.9. Removal and installation of the oil pallet
      + 4.2.10. The oil pump
      4.2.11. Removal and installation of pistons and rods
      4.2.12. Removal and flywheel installation
      4.2.13. Removal and installation of a forward sealing ring of a cranked shaft
      4.2.14. Removal and installation of support of the power unit
      4.2.15. Replacement of a back sealing ring of a cranked shaft
      + 4.2.16. A cranked shaft and radical bearings
      4.2.17. Check of details of the engine
      4.2.18. System of greasing and ventilation system картера
      4.2.19. Removal and engine installation
      4.2.20. Start of the engine after major repairs
   + 4.3. Engine DOHC with 16 valves
   + 4.4. Diesel engines 16D and 16DА
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

4.2.9. Removal and installation of the oil pallet Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports.
2. Merge engine oil in the suitable container and establish маслосливную a stopper into place.
3. Unscrew bolts, fastening a reception exhaust pipe to an inlet collector.
4. Unscrew bolts, fastening a protective plate of a flywheel, and remove a plate.
5. Unscrew bolts and remove the oil pallet from the engine.
6. On later models if necessary unscrew a bolt of fastening of an arm маслоприемной tubes.
7. Remove маслоотражательную a partition and a lining. On a part of models the rubber lining (it is shown in drawing at the left), and on other models – two pith linings (drawing on the right) is used.

Installation

PERFORMANCE ORDER
1. If on later models the plate acted in film маслоулавливающая, clear interfaced surfaces and establish a plate with a new lining or linings. Establish an arm supporting маслоприемную a pipe, and fix its bolt.
2. Clear the oil pallet in kerosene or solvent and remove all external dirt and an internal sediment. Clear of the rests of an old lining interfaced surfaces of the oil pallet and the block of cylinders and check up that they pure and dry.
3. Apply a thin film hermetic on the case of the oil pump and interfaced surfaces of the oil pallet and a back radical cover of the bearing, then establish a new lining of the oil pallet.
4. Apply a thin film hermetic on an interfaced surface of the oil pallet and a carving of bolts of fastening of the oil pallet. Establish the oil pallet into place and fix bolts, having tightened them gradually and in diagonal sequence.
5. Screw a reception exhaust pipe on a final collector. Establish a protective plate of a flywheel and lower the car on the earth. Fill in in the engine engine oil.


On the main page