Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   + 4.1. Engine OHV (with a camshaft in the block of cylinders)
   - 4.2. Engines OHC
      4.2.1. A technical characteristics
      4.2.2. Compression check
      + 4.2.3. The repair operations demanding removal of the engine
      4.2.4. Removal and installation of auxiliary elements of the engine
      4.2.5. Removal and installation of the valve of adjustment of pressure of oil
      + 4.2.6. A gear belt
      + 4.2.7. A head of the block of cylinders
      4.2.8. Removal and camshaft installation
      4.2.9. Removal and installation of the oil pallet
      - 4.2.10. The oil pump
         4.2.10.1. Removal and installation
         4.2.10.2. Repair of the oil pump
      4.2.11. Removal and installation of pistons and rods
      4.2.12. Removal and flywheel installation
      4.2.13. Removal and installation of a forward sealing ring of a cranked shaft
      4.2.14. Removal and installation of support of the power unit
      4.2.15. Replacement of a back sealing ring of a cranked shaft
      + 4.2.16. A cranked shaft and radical bearings
      4.2.17. Check of details of the engine
      4.2.18. System of greasing and ventilation system картера
      4.2.19. Removal and engine installation
      4.2.20. Start of the engine after major repairs
   + 4.3. Engine DOHC with 16 valves
   + 4.4. Diesel engines 16D and 16DА
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes

4.2.10. The oil pump

4.2.10.1. Removal and installation Removal

PERFORMANCE ORDER
1. Remove a gear belt, the oil pallet, маслозаборную a tube of the oil pump and маслоотражательную a plate.
2. Unscrew a bolt of fastening of a pulley of a cranked shaft and remove a pulley together with linings. Thus note their arrangement.
3. Remove segment шпонку (it is specified by an arrow) from a cranked shaft.
4. Unscrew bolts and remove a back casing of a gear belt. On later models for removal of a back casing of a gear belt it is preliminary necessary to remove a camshaft pulley.
5. Unscrew two bolts, fastening маслоприемную a pipe to the case of the oil pump and one bolt, крепящий an arm of support of a pipe to a cover of the central radical bearing (fastening bolts маслоприемной tubes are specified by arrows). Remove маслоприемную a pipe. On models with an oil radiator ослабьте connecting nuts also disconnect pipes from the case of the oil pump.
6. Unscrew bolts and remove the oil pump from a forward part of the block of cylinders. Remove a lining of the oil pump.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal, taking into account following moments.
2. Check up that interfaced surfaces of the case of the oil pump and the block of cylinders pure and dry and establish a new lining of the oil pump, preliminary having put on both parties of a lining a thin layer of hermetic.
3. For protection of working edges of a sealing ring at installation of the oil pump wrap up a sticky tape a cranked shaft.
4. Establish the oil pump, thus an internal rotor of the pump should settle down correctly on шестиграннике a cranked shaft. Screw in bolts of fastening of the oil pump and tighten their demanded moment. Remove a sticky tape from a cranked shaft.
5. Establish маслоотражательную a plate, маслозаборную a pipe of the oil pump and the oil pallet.
6. Establish a back casing of a gear belt, a gear belt and adjust a tension of a gear belt.


On the main page