Opel Kadett E

1984-1991 of release

Repair and car operation



Opel Kadett E
+ 1. The maintenance instruction
+ 2. Weekly checks and service in a way
+ 3. Maintenance service
- 4. The engine
   + 4.1. Engine OHV (with a camshaft in the block of cylinders)
   + 4.2. Engines OHC
   - 4.3. Engine DOHC with 16 valves
      4.3.1. A technical characteristics
      4.3.2. Compression check
      + 4.3.3. The operations demanding removal of the engine
      4.3.4. Removal of auxiliary components of the engine
      4.3.5. Removal and installation of the valve of adjustment of pressure of oil
      - 4.3.6. A gear belt
         4.3.6.1. Removal of a gear belt
         4.3.6.2. Installation of a gear belt
         4.3.6.3. Adjustment of a gear belt
      4.3.7. Removal and installation of the mechanism of a tension of a gear belt and rollers
      4.3.8. Removal, check and installation of camshafts
      + 4.3.9. A head of the block of cylinders
      4.3.10. Removal and installation of the oil pallet and маслоотражательной plates
      + 4.3.11. The oil pump
      4.3.12. Removal and installation of the valve of the thermostat of an oil radiator
      + 4.3.13. Pistons and rods
      4.3.14. Removal and flywheel installation
      + 4.3.15. Replacement of sealing rings
      4.3.16. Removal, check and installation of bearings of a cranked shaft
      4.3.17. Check of components of the engine
      4.3.18. Removal and engine installation
      4.3.19. Start of the engine after major repairs
   + 4.4. Diesel engines 16D and 16DА
   + 4.5. Diesel engines of 1,7 l
+ 5. System of cooling, heating and ventilation
+ 6. Fuel and exhaust systems
+ 7. Start and gymnastics system
+ 8. Ignition system
+ 9. Coupling
+ 10. Transmissions and power shafts
+ 11. Brake system
+ 12. A suspension bracket and a steering
+ 13. A body
+ 14. Electric schemes





4.3.6.3. Adjustment of a gear belt
THE GENERAL DATA

Special tool Opel № КМ-666 for measurement of a tension of a gear belt


Adjustment of a tension of a gear belt make on the cold engine.

PERFORMANCE ORDER
Adjustment with use of special tool Opel KM-666
1. Remove a casing of a gear belt and, having weakened a bolt of fastening of a pulley of the mechanism of a tension, check up that labels ВМТ on pulleys of a camshaft and a cranked shaft have been combined with indexes. If necessary tighten a cranked shaft that labels were combined.
2. According to the instruction establish special tool KM-666 on an arm of a pulley of the mechanism of a tension
3. Note the seventh tooth, considering counter-clockwise from label ВМТ on a pulley of the camshaft operating final valves.
4. Turn a cranked shaft of the engine clockwise before combination of noted tooth with the index of the top dead point on a cover of a head of the block of cylinders. Rotate a cranked shaft in regular intervals and smoothly to exclude перескакивание a gear belt on teeths of pulleys. Tighten a bolt of fastening of a pulley of the mechanism of a tension the demanded moment.
5. Remove the special tool.
Adjustment without the special measuring tool
6. Remove a casing of a gear belt and, having weakened a bolt of fastening of a pulley of the mechanism of a tension, check up that labels ВМТ on pulleys of a camshaft and a cranked shaft have been combined with indexes. If necessary tighten a cranked shaft that labels were combined.
7. Turn a pulley of the mechanism of a tension to a gear belt so that in the centre of the longest branch of a belt the belt could be turned on 90 hand fingers, putting moderate effort. In the presence of spring scales or a steelyard and a steel ruler check up a deflection of a belt which should make 10 mm under loading of 9 kg.
8. Fix a pulley of the mechanism of a tension in this position and tighten a bolt of fastening of a pulley the demanded moment.
9. Turn a cranked shaft of the engine clockwise on two complete revolutions and check up that labels ВМТ on pulleys of a cranked shaft and camshafts were combined with indexes.
10. Establish an external casing of a gear belt. Check up, that rubber sealing rings in apertures under screws have fallen into place, then fix a casing screws.
11. Establish a belt of a drive of the generator and adjust its tension.
13. Establish the air filter.
14. Connect a weight wire to the accumulator.
15. After adjustment of a tension of a gear belt at the first possibility address on servicing deport for carrying out of adjustment with use of special tools.
16. The further installation is made in sequence, return to removal.

On the main page