Subaru Legacy/Outback

1999-2003 of release

Repair and car operation


Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
- Systems of cooling, heating
   Specifications
   + System of cooling of the engine
   - Heating/ventilation/air conditioning systems
      Removal and installation дефлекторов and air lines
      Removal and installation of resistive assemblage drive the electromotor of the fan of a heater
      Removal, check and installation drive the electromotor of the fan of a heater
      Removal and installation of the control panel by functioning of systems of heating/ventilation/air conditioning
      Removal and installation of assemblage of a heater
      Removal and installation of the heat exchanger of a heater
      Check of serviceability of functioning and service of systems of heating and air conditioning
      Compressor K/V - a design and a functioning principle
      Condenser K/V - a design and a functioning principle
      Receiver-dehumidifier К/В - a design and a functioning principle
      The gauge-switch of pressure К/В - a design and a functioning principle
      Evaporator K/V - a design and a functioning principle
      Broad valve K/V - a design and a functioning principle
      Condition check, removal and installation of the compressor of system K/V
      Removal and installation of the condenser of system K/V
      Removal and installation of a receiver-dehumidifier of system K/V
      Removal and installation of the inlet block of system K/V, evaporator replacement
      Replacement of connecting hoses of a refrigerator path
      Check of serviceability of functioning of the gauge-switch of pressure
      Removal and installation of information gauges of system of an automatic central air (climate control)
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal and installation of the control panel by functioning of systems of heating/ventilation/air conditioning

Details of installation of the control panel are shown by functioning of systems of heating/ventilation/air conditioning on illustrations.

Details of installation of the control panel functioning of systems of heating/ventilation/air-conditioning on hand-operated models К/В

1 — the Push-button switch
2 — the management Handle
3 — the Control panel
4 — the Bearing module
5 — the Cover

6 — the Cable of a drive mixing заслонки
7 — the Switch of a choice of a high-speed mode of functioning of the fan
8 — the Printed-circuit board
9 — illumination Lamps


Details of installation of the control panel functioning of systems of heating/ventilation/air-conditioning on models with automatic К/В

1 — the Control panel
2 — the Printed-circuit board
3 — the Electronic block of management
4 — the Casing

5 — Aspiratornyj a hose
6 — the Gauge of temperature of air in salon
7 — illumination Lamps


Hand-operated models К/В

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove forward section of furnish of the central console (), then turn out 2 fixing screws () and remove the central section of furnish of the panel of devices (D).
3. Turn the handle of a choice of a temperature mode in extreme left position (FULL HOT) and disconnect from a heater a cable of a drive mixing заслонки.

4. Release fixing screws and slightly liberate the block of management from console section of the panel of devices.

5. Disconnect an antenna cable and remove assemblage.
6. Installation is made upside-down, - track, that the handle of a choice of a temperature mode remained turned in extreme left position (FULL HOT).


The models equipped with an automatic central air of air

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove forward section of furnish of the central console (), then turn out 2 fixing screws () and remove the central section of furnish of the panel of devices (D).

3. Release fixing screws and slightly liberate the block of management from console section of the panel of devices.

4. Installation is made upside-down.


On the main page