Citroen Xantia

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).

2. Prop up противооткатными boots back wheels, поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel. Whenever possible, easing of a nut of fastening of a power shaft should be made to поддомкрачивания the car:
   a) Prop up противооткатными boots forward wheels and remove decorative caps of wheel disks;
   b) Firmly cock a lay brake;
   c) Take a R-shaped clamp and remove a lock cap of a nut;
   d) Oslabte a nut by means of a suitable face key.

3. Loosen the and partially turn away a nut of a spherical finger of a tip of steering draught on ступичной to assemblage (turn away a nut till the end of a carving for the purpose of protection of coils by last at hinge liberation). Liberate шаровый a finger of a tip from ступичной assemblages by means of a divider of spherical support, then definitively remove a nut.

4. Отболтите from a rack also shift aside a basic arm of electroconducting / of a hydraulic hose.

5. Remove a brake disk (address to the Head Brake system). Loosen the and partially turn away a nut of a finger of the bottom spherical support (turn away a nut till the end of a carving fingers for the purpose of protection of coils by last at hinge liberation). Liberate шаровый a finger from ступичной assemblages by means of a divider of spherical support, then definitively remove a nut.
6. Liberate the external end of a power shaft from ступичной assemblages (Power shafts see the Head). Pay attention to following moments:
   a) There is no necessity to merge трансмиссионное oil from a transmission;
   b) do not liberate an internal pin of a power shaft from transmission, and at work from the right board of the car do not liberate also the intermediate bearing of a shaft;
   c) the Wire tie up the free external end of a power shaft to a suspension bracket element.

7. Give a nut of a coupling bolt of a collar of fastening ступичной assemblages on a suspension bracket rack.

8. With the help пруткового a key on 8.0 mm dissolve a groove of a collar of fastening ступичной assemblages on suspension brackets (enter шестигранный пруток into a groove and turn it on a turn quarter). Simultaneously lower ступичную assemblage downwards, removing it from a rack.

1. Dissolve a fastening collar ступичной assemblages with the help пруткового a key (the previous subsection, last point see).
2. Put on ступичную assemblage a suspension bracket rack (the directing ledge on a rack should get a collar groove).
3. Push a nave upwards on a rack against the stop it in bearing coat hanger.
4. Establish a coupling bolt (a bolt it is necessary to fill in a collar in front), screw a new nut and tighten it with demanded effort.
5. Establish into place a brake disk and a support, connect a cable of a drive of a lay brake (address to the Head Brake system).
6. Fill in a nave a power shaft pin, screw and tighten a fixing nut (Power shafts see the Head). Whenever possible the nut should be tightened after car lowering on the earth.
7. Establish on a suspension bracket rack bearing arm of electroconducting / of a hydraulic hose and fix its two bolts.
8. Connect to ступичной to assemblage a tip of steering draught, having fixed шаровый a finger a new nut. Tighten a nut of a spherical finger with demanded effort.
9. Establish into place a wheel, then lower the car on the earth and tighten wheel (and ступичную) nuts with demanded effort.
10. Tighten спускной the gate of a regulator of pressure and translate a control lever a suspension bracket in position "Maximum".
11. In summary make adjustment of corners of installation of forward wheels (Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels see).