Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of tips of steering draughts

Removal

New nuts of spherical fingers be required.


 PERFORMANCE ORDER

1. Prop up back wheels of the car, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
2. Loosen the and partially turn away a nut of a spherical finger of fastening of a tip of steering draught on ступичной to assemblage, then liberate a finger from a reception nest by means of a divider of spherical support. Remove a nut.
3. If the tip is used further, mark its position to a draught bar.
4. Fix a bar of draught from проворачивания and give on a half-turn a counternut.
5. Precisely having counted quantity of turns on a carving, turn out and remove from draught its tip.
6. Count and write down quantity of the bared coils of a carving from an end face of the spherical hinge of a tip to a counternut. Check up serviceability of a condition of a tip, its protective cover, a shaft and a carving of a spherical finger. In case of revealing of the hinge specifying in deterioration люфта or mechanical damages make replacement.
7. Carefully clean a carving on a draught bar.

Installation

 PERFORMANCE ORDER

1. At installation of a new tip transfer on it an old counternut, having screwed it so that that the quantity of the bared coils of a carving corresponded to the value fixed in the course of dismantle.
2. Screw a tip in draught on the quantity of turns counted in the course of dismantle. Thus the tip counternut should appear отстоящей from an emphasis on a turn quarter (be verified with the marks put earlier).
3. Fix a tip in ступичной to assemblage and screw a new nut of a spherical finger, having tightened it with demanded effort.
4. Establish a wheel, then lower the car on the earth and tighten wheel bolts with demanded effort.
5. Check up corners of installation of forward wheels (Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels see), then strongly tighten a counternut of a tip of steering draught.



On the main page