Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of naves of back wheels

Removal

Do not remove a nave of back wheels without special necessity on that. For tightening of a nave from a pin of the back bridge the special stripper is required, and performance of the given procedure always is connected with risk of damage ступичных bearings. At assemblage the nut with a protective cap is required new ступичная.


 PERFORMANCE ORDER

1. Remove a back brake disk (address to the Head Brake system).

2. By means of a hammer and the big screw-driver with a flat sting accurately remove the central cap of protection ступичной nuts (at assemblage the cap is subject to replacement without fail).

3. By means of a hammer and a chisel расчеканьте ступичную a nut.

4. By means of a face key with a long collar ослабьте also turn on ступичную a nut, then take a persistent washer.

At assemblage the nut is subject to replacement without fail.

5. By means of a stripper pull together a nave from a pin of the back bridge in gathering with an external holder ступичного the bearing. Having removed a nave, take advantage of a stripper for removal from a pin of an internal holder of the bearing. Afterwards remove the remote plug (try to remember its adjusting position).
6. Establish holders on the bearing and check up freedom of its rotation. Composers of the present Management urgently recommend to make replacement ступичного the bearing without fail in view of high degree of probability of damage of assemblage in the course of nave dismantle. The last means necessity of replacement of all ступичной assemblages as bearings in an individual order are not delivered.
7. Having removed a nave, estimate degree of deterioration of a pin of the back bridge, check up it on presence of mechanical damages, in case of need make replacement. Pin assemblage fastens on the bridge by means of a lock ring and can be brought down by means of a hammer with soft brisk, or is removed by means of a powerful stripper. At installation of a new nave track, that it шлицы in the correct image have entered into gearing with шлицами the longitudinal lever of a suspension bracket. Pin landing is carried out by means of a press, or approaching on the size оправки and a hammer. Do not forget to replace a lock ring.

Installation

 PERFORMANCE ORDER

1. Grease a bridge pin with pure impellent oil, plant on it the remote plug, having tracked correctness of its placing.
2. Plant on a pin an internal holder new ступичного the bearing, having begun to knock its hammer through tubular оправку.

Оправка should rest only against a flat face surface of a holder.

3. Check up, whether the bearing is filled by greasing and plant ступичную assemblage on a bridge pin. By means of tubular оправки plant an external holder of the new bearing.
4. Establish a persistent washer, then screw new ступичную a nut, having tightened it with demanded effort. Reliably зачеканьте a nut, then plant a new protective cap.
5. Establish a brake disk (address to the Head Brake system).



On the main page