Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket

Stabilizer bar

Самоконтрящиеся nuts “Nylock” at assemblage are subject to replacement without fail.

Removal


Details of fastening of the proof-reader of height of a road gleam

1 — the Coupling bolt of a collar of fastening on a bar of the stabilizer of the proof-reader
2 — the Coupling bolt of a collar of fastening on a bar of the stabilizer of the gauge of movings of a body
3 — the Point of a detachment of the gauge
4 — Bolts of fastening of a basic plate of the proof-reader
5 — the Point of a detachment from the proof-reader of the lever of manual adjustment of a road gleam


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).
2. Prop up противооткатными boots back wheels, then поддомкратьте redock of the car and establish it on props. Remove forward wheels.
3. Under the car remove a cap from a nut of the cranked lever of a drive of a gear change, then give a nut and disconnect приводную draught from an axis on a stretcher.
4. Turn out bolts of fastening of assemblage of the steering mechanism on a stretcher, remove remote washers.
5. Turn out a coupling bolt of a collar of fastening of the proof-reader of height of position of a suspension bracket on a bar of the stabilizer of cross-section stability.
6. On models with a hydroactive suspension bracket turn out a bolt of a collar of fastening to a bar of the gauge of moving of a body (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam). Disconnect from the gauge the executive lever.
7. Turn out two bolts of fastening of a basic plate of the valve of the proof-reader of height of a suspension bracket to a stretcher (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam).
8. Loosen the a coupling bolt also disconnect the lever of manual adjustment of a road gleam from assemblage of the proof-reader of height of a suspension bracket (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam).
9. Accurately having hooked, liberate the plastic lever of the proof-reader of height of position of a suspension bracket from the spherical hinge on the executive lever.
10. From both parties of a stretcher liberate brake tubes from basic arms (separate from a tube a flexible hose, then liberate a tube from clips on a stretcher) (address to the Head Brake system).
11. Examine a stretcher and liberate from its clips all hydraulic lines and electroconducting plaits. Some of tubes/hoses should be disconnected. Try to remember routes of a lining of lines of communication, prepare for gathering of spilt fuel. The open ends of the disconnected lines and their unions at once закупорьте for the purpose of minimisation of losses of a liquid and in order to avoid hit in dirt system.

12. Give болтовое connection of fastening of an arm of a back support of the power unit to a rubber pillow.

13. From both parties of a stretcher turn out fastening bolts to it локеров wheel arches.
14. In the right back corner of a stretcher turn out two bolts and remove a collar of fastening directing wires/tubes. For collar removal beat out the central finger.
15. Turn out three bolts of fastening of basic arms of plaits electroconductings/tubes in the left back corner of a stretcher.
16. Remove a collar of fastening directing lines of communication in the left back corner of a stretcher (for collar removal beat out the central finger).
17. Disconnect from the ends of a bar of the stabilizer its basic racks (the subsection "Racks of the stabilizer of cross-section stability - Removal" see, item 2).
18. Once again make sure that nothing remains connected and does not disturb to stretcher dismantle.
19. Turn out back bolts of fastening to a stretcher of the bottom levers of a suspension bracket. Pay attention that the most back serve also for fastening of collars of fastening of a bar of the stabilizer. Remove collars of fastening of a bar.
20. Prop up a stretcher тележечным a jack through wooden prorates.
21. Turn out six fixing bolts and slightly lower a stretcher on a jack.
22. Remove rubber plugs of collars from a bar of the stabilizer of cross-section stability.

23. Lower a stretcher approximately on 100 mm and take a bar of the stabilizer from under the car.

Installation

Installation is made upside-down. Pay attention to following moments:


Details of fastening of the bottom lever of a suspension bracket / a fixing collar of a bar of the stabilizer of cross-section stability

And — the Control size
1 — the Collar of fastening of a bar
2 — the Fixing bolt

     a) Arrange a bar of the stabilizer of cross-section stability so that the size ((see an illustration of the Detail of fastening of the bottom lever of a suspension bracket / a fixing collar of a bar of the stabilizer of cross-section stability) between fixing apertures of a rack and the bottom surface of a stretcher made 21 ± 2 mm, then tighten bolts of fastening of the bottom levers/collars of fastening of a bar;
   b) do not tighten a collar of fastening of the proof-reader of height of position of a suspension bracket and the gauge of movings of a body until the size of a road gleam will be adjusted;
   c) do not forget to replace all самоконтрящиеся a nut;
   d) All fixture tighten with demanded effort;
   e) Track correctness of a lining and reliability of fastening of lines of communication where it is required, replace sealing муфты штуцерных sockets;
   f) After car lowering on the earth tighten спускной the gate of a regulator of pressure and translate a control lever a suspension bracket in position "Maximum" (the Uniform hydraulic system see the Head);
   g) Check up liquid level in the tank of hydraulic system, in case of need make corresponding updating (address to the Head Routine maintenance);
   h) Pump over brake system (address to the Head Brake system);
   i) In summary check up adjustment of height of a road gleam (Check of installation and adjustment of a road gleam see), then tighten collars of fastening of the proof-reader and (at a corresponding complete set) the gauge of movings of a body.

Racks of the stabilizer of cross-section stability

New fixing nuts be required.

Removal

 PERFORMANCE ORDER

1. Prop up противооткатными boots back wheels of the car, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
2. Partially ослабьте a nut of fastening of a rack of the stabilizer on the end of its bar. Disconnect a bar from a rack by means of a divider of spherical support, then definitively remove a nut.

At отдавании the rack finger can be kept nuts from проворачивания with the help пруткового a key on 5.0 mm.

3. Give a fixing nut and disconnect a rack of the stabilizer from a suspension bracket rack (for keeping of a finger from проворачивания, as before, take advantage прутковым of a key on 5.0 mm). In case of need take advantage of a divider of spherical support, however do not forget to screw before thus a nut on the end of a carving part of a finger not to damage carving coils.

4. Remove a rack of the stabilizer of cross-section stability from the car.

Installation

Installation is made upside-down. Do not forget to replace fixing nuts. Track observance of demanded efforts of a tightening of fixture.



On the main page