Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of longitudinal levers of a back suspension bracket

Removal

The new nut of an axis of the rotary lever is required.


 PERFORMANCE ORDER

1. Prop up противооткатными boots forward wheels and cock a lay brake, then поддомкратьте a back of the car and establish it on props. Remove a corresponding back wheel.
2. Remove the corresponding hydraulic block of a back suspension bracket (Removal and installation of hydraulic blocks of a back suspension bracket see).

3. On equipped ABS models execute following procedures:
   a) Turn out three fixing screws and remove a brake board;
   b) Turn out a fixing bolt and remove wheel gauge ABS. Shift the gauge aside, watching that it has not appeared its electroconducting is tense;
   c) Remove a thermofilter of the wheel gauge.

4. Release штуцерный a socket and disconnect from a brake support a hydraulic tube. At once закупорьте the open ends of a tube and the union of its connection in order to avoid hit in dirt system.
5. Liberate hydraulic tubes from intermediate clamps on the longitudinal lever and assemblage of the back bridge.
6. Get a jack under located with an opposite board of the car the longitudinal lever and cock it so that the lever has appeared is parallel to the earth.

7. Turn out two bolts of fastening to subject removal to the longitudinal lever of a bar of the stabilizer of cross-section stability. Pay attention that one of bolts is used also for fastening of a basic arm of a hydraulic tube.

8. Give a nut of an axis of the rotary lever.

9. Get wooden брусок between a bar of the stabilizer of cross-section stability and a car body, then take advantage of it as the lever for assignment of a bar from a body. Try not to suppose a tension of the hydraulic tubes fixed in arms over the end of a bar of the stabilizer.
10. Take an axis of the longitudinal lever, then remove from the car the lever.

Installation

Installation is made upside-down. Pay attention to following moments:
   a) Before installation it is necessary to grease an axis of the longitudinal lever on all length;
   b) do not forget to replace a nut of an axis of the lever. Track observance of efforts of a tightening of fixture;
   c) the Description of procedure of installation of the hydraulic block is resulted in section Removal and installation of hydraulic blocks of a back suspension bracket;
   d) In summary do not forget to pump over hydraulic system (address to the Head Brake system).


On the main page