Citroen Xantia

Since 1993 of release

Repair and car operation

Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket

Removal

Самоконтрящиеся nuts “Nylock” at assemblage are subject to replacement without fail. Where it is required, replace also sealing муфты штуцерных sockets of hydraulic tubes.

Components of rack-mount assemblage of a forward suspension bracket

1— The Nut of the hydraulic cylinder of a suspension bracket
2— The suspension bracket Cylinder on a body (25 Nanometers)
3— Fastening of a bar of the stabilizer of cross-section stability (40 Nanometers)

4 — Fastening of a bar of the stabilizer of cross-section stability (40 Nanometers)
5 — the Nut of the spherical hinge (45 Nanometers)

PERFORMANCE ORDER

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).
2. Prop up противооткатными boots back wheels, then поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
3. Get suitable drain capacity under спускной the gate of a hydraulic regulator and, a way нажимания on the bottom lever, let out from the hydraulic block of a suspension bracket as much as possible liquid.
4. Give a fixing nut and disconnect a rack of the stabilizer of cross-section stability from a suspension bracket rack. The general view of rack-mount assemblage is shown on an illustration Components of rack-mount assemblage of a forward suspension bracket. For keeping of a rack-mount finger from проворачивания take advantage прутковым of a key on 5.0 mm. Be in case of need ready to apply a divider of spherical support to a partition of components (do not forget to take care thus of carving protection, having screwed on some coils a nut).
5. Отболтите from a rack of a suspension bracket also shift aside a basic arm of lines of communication. Track, that plaits of electroconducting and hoses have not appeared are excessively tense.

6. Give a nut of a coupling bolt of a collar of fastening ступичной assemblages on a suspension bracket rack.

7. With the help пруткового a key on 8.0 mm unclench a collar (the subsection "Removal and installation ступичной assemblages of a forward suspension bracket - Removal" see, last point) and remove ступичную assemblage from a suspension bracket rack.

8. Disconnect a returnable hydraulic tube from a suspension bracket rack for what have a bite бокорезами a fixing collar and liberate the end of a tube from a rack. Prepare for gathering of a spilt liquid, at once закупорьте the open ends of a tube and reception port in a rack in order to avoid hit in dirt system.

9. Further operate as directed, resulted in corresponding subsections (depending on volume of forthcoming works).

Rack removal complete with the hydraulic block

PERFORMANCE ORDER

1. In an impellent compartment release штуцерный a socket and disconnect a tube of giving of a liquid from the hydraulic block. At once закупорьте the open ends of a tube and the reception union of the hydraulic block for the purpose of minimisation of losses of a liquid and in order to avoid hit in dirt system. Отболтите from the hydraulic block a basic arm () tubes.

2. Turn out four bolts of fastening of the hydraulic block to a car body.

3. Lift assemblage upwards and take it through an impellent compartment, accurately passing a tube of giving of a hydraulic liquid through an aperture in кузовной panels.

Rack removal in an individual order

PERFORMANCE ORDER

1. In a wheel arch separate a protective cover from the basis of the hydraulic block.

2. Having hooked, remove a plastic cover, then ослабьте накидную a nut штуцерного a socket of fastening of a hydraulic tube to the top part of a rack (in case of need block a rack from проворачивания with the help шлицевого a key).

3. Moisten a cone of a rack of a suspension bracket (under a nut) getting oil for the purpose of simplification of procedure of branch of assemblage from the hydraulic block.
4. Turn away a nut and take a rack through a wheel arch.

Installation

Rack in gathering with the hydraulic block

PERFORMANCE ORDER

1. Get assemblage on the regular place. Track, that there was no giving of a liquid jammed a tube. Screw bolts of fastening of the hydraulic block and tighten them with demanded effort.
2. Connect to the block submitting tube (do not forget to replace a sealing washer) and tighten штуцерный a socket.
3. Pass to performance of the procedures described more low, since subsection "General procedures", item 1.

Suspension bracket rack

PERFORMANCE ORDER

1. Grease the top part of a cone of a rack and sealing surfaces hydraulic liquid LHM.
2. Cover a carving part of a rack with fixing hermetic, then get assemblage on the regular place in a wheel arch. Screw a fixing nut and tighten it with demanded effort.
3. Fix on the basis of the hydraulic block a protective cover.

The general procedures

PERFORMANCE ORDER

1. With the help пруткового a key unclench a fastening collar ступичной assemblages.
2. Put on ступичную assemblage a suspension bracket rack, having tracked, that the directing ledge has got to a collar groove.
3. Push ступичную assemblage against the stop bearing coat hanger on a rack.
4. Insert a coupling bolt (from the forward party of a rack), screw on it a new nut and tighten it with demanded effort.
5. Connect to a rack of a suspension bracket a rack of the stabilizer of cross-section stability and tighten a new nut of a spherical finger with demanded effort.
6. Establish on a rack a basic arm of lines of communication and fix its two bolts.
7. Connect to a rack a returnable tube (do not forget to replace in case of need a sealant) and fix its new collar.
8. Establish a wheel, lower the car on the earth and tighten wheel bolts with demanded effort.
9. Tighten спускной the gate of a regulator of pressure and translate a control lever a suspension bracket in position "Maximum".
10. Check up level of a hydraulic liquid, in case of need make corresponding updating (address to the Head Routine maintenance).

On the main page