Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of assemblage of the back bridge

Removal

At a corresponding complete set prepare new sealing муфты штуцерных sockets of hydraulic tubes.


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).
2. Prop up противооткатными boots forward wheels, firmly cock a lay brake, then поддомкратьте a back of the car and establish it on props. Remove back wheels.
3. Remove a spare wheel with an arm of its fastening under the car.

4. Turn out fixing bolts and remove a connecting bar from assemblage of the back bridge.

5. Remove back and intermediate sections of system of release of the fulfilled gases (Systems of decrease in toxicity and release of the fulfilled gases see).
6. Loosen the a coupling bolt also disconnect an executive rod of manual adjustment of a road gleam from assemblage of the hydraulic proof-reader.
7. On the models equipped with a hydroactive suspension bracket, disconnect the gauge of movings of a body.
8. On models with ABS disconnect electroconducting from wheel gauges.
9. Disconnect tubes of giving and return of a liquid from assemblage of the hydraulic regulator established in the central part of the back bridge. Prepare for gathering of a spilt liquid, at once закупорьте the open ends of lines and unions of their connection for the purpose of minimisation of losses of a hydraulic liquid and in order to avoid hit in dirt system.

10. Examine assemblage of the bridge and liberate from intermediate clamps all hydraulic and electric lines of communication, disturbing to the further dismantle of the bridge. Some of lines should be disconnected. Try to remember routes of a lining of all wires, tubes and hoses. The open ends of lines at once закупорьте in order to avoid hit in dirt system.

11. Disconnect tubes of gasoline pipe lines from a fuel tank and liberate them from intermediate clamps on the car bottom.
12. Prop up assemblage of the back bridge by a jack through wooden брусок. Track, that the emphasis had on bearing lateral beams.

13. Turn out four bolts of fastening of assemblage of the back bridge.
Above — the Forward bolt of fastening of assemblage of the back bridge
Below — the Back bolt of fastening of assemblage of the back bridge



14. Slightly lower assemblage on a jack.
15. Last time make sure, no communication tenches remained connected.
16. Slightly submit bridge assemblage back on purpose обведения a jellied mouth of a fuel tank.
17. Lower bridge assemblage on a jack and take it from under the car.

Installation

Installation is made upside-down. Pay attention to following moments:
   a) Track correctness of a lining and reliability of fastening of all lines of communication;
   b) At a corresponding complete set replace sealing elements штуцерных sockets of hydraulic tubes;
   c) All fixture tighten with demanded effort;
   d) Tighten спускной the gate of a regulator of pressure and translate a control lever a suspension bracket in position "Maximum";
   e) In summary pump over brake system (address to the Head Brake system).

On the main page