Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of hydraulic blocks of a back suspension bracket

For отворачивания from the hydraulic block of a spherical receiver the tape key is required. At receiver installation the new sealing lining is required. The worn out sealing elements штуцерных sockets of hydraulic tubes also are subject to replacement.


Components of the hydraulic block of a back suspension bracket

And — the Tube of giving of a hydraulic liquid
In — the Spherical receiver
With — the Spring clamp of fastening of a connecting bar of a suspension bracket
D — the Spring clamp of fastening of the hydraulic block


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).
2. Поддомкратьте the car also establish it on props. Remove a corresponding back wheel.
3. Get under спускной the gate of a regulator of pressure suitable drain capacity. A way отжимания upwards the longitudinal lever of a suspension bracket extort from the hydraulic block the greatest possible quantity of a liquid.
4. By means of a tape key ослабьте landing of a spherical receiver, then turn out it from assemblage of the hydraulic block.
5. Disconnect from the hydraulic block a tube of giving of a liquid. At once закупорьте the open ends of a tube and штуцерного a socket in order to avoid hit in dirt system.
6. Remove a spring clamp from a connecting bar of a suspension bracket (Components of the hydraulic block of a back suspension bracket see an illustration).
7. Remove a spring clamp of fastening of the hydraulic block.
8. Remove the hydraulic block from assemblage of the back bridge and disconnect from it returnable hydraulic and ventilating tubes.

Installation

 PERFORMANCE ORDER

1. Connect to the hydraulic block returnable and ventilating tubes and get assemblage on the regular place. Track, that tubes have not appeared are jammed.
2. Fix the hydraulic block a spring clamp.
3. Establish into place a clamp of a connecting bar of a suspension bracket.
4. Connect to the hydraulic block a tube of giving of a liquid. At a corresponding complete set replace a sealing element штуцерного a socket.
5. Grease a contact surface of a spherical receiver and establish it on the hydraulic block (do not forget to replace a sealing lining).
6. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with demanded effort.
7. Tighten спускной the gate of a hydraulic regulator of pressure and translate a control lever a suspension bracket in position "Maximum".
8. Start the engine and examine all disconnected and acting in film components on presence of signs of leaks.
9. Check up level of a hydraulic liquid, in case of need make corresponding updating (address to the Head Routine maintenance).



On the main page