Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
+ Engine repair
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation ступичной assemblages of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major repairs and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblages of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement back ступичных bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assemblage of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and steering wheel installation
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assemblage of the switch of ignition/lock of a steering column
   The steering mechanism - the general data, removal, major repairs and installation
   System of hydrostrengthening of a wheel - the general data
   Removal and installation of tips of steering draughts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal and installation of a stretcher of a forward suspension bracket

Removal

The divider of spherical support is required. All самоконтрящиеся nuts at assemblage are subject to replacement without fail.


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (the Uniform hydraulic system see the Head).
2. Поддомкратьте the car also establish it on props. Remove forward wheels.
3. Under the car remove a protective cover from a nut of the cranked lever of a drive of a gear change, give a nut and disconnect draught of switching from the rotary support on a stretcher.

4. Turn out fastening boats to a mechanism stretcher реечной steering transfer, remove remote plugs. A wire tie up assemblage of the steering mechanism to system of release of the fulfilled gases.

5. Give a nut and take a bolt of fastening of an arm of a back support of the power unit to the rubber pillow.

6. From both parties of the car turn out fastening bolts локеров wheel arches to a stretcher.
7. Serially ослабьте and partially turn away a nut of fingers of both bottom spherical support, then divide support by means of the special tool. After liberation of spherical fingers definitively remove nuts from their shafts.
8. Operating in the same manner, by means of a divider of spherical support serially disconnect racks of the stabilizer of cross-section stability from the ends of its bar. At отдавании nuts the rack finger can be kept from проворачивания with the help пруткового a key on 5.0 mm.
9. From the left board of the car ослабьте and partially turn away a nut of a spherical finger of fastening of a tip of steering bent for ступичной to assemblage. Liberate a finger from the landing nest by means of a divider of spherical support, then definitively remove a nut.

10. In the right back corner of a stretcher turn out two bolts and release a clamp of fastening directing lines of communication (wires and hydraulic tubes). For отпускания a clamp beat out its central pin.

11. On the models equipped with a hydroactive suspension bracket disconnect electroconducting from the gauge of movings of a body.

12. Turn out two bolts of fastening клапанной assemblages of the proof-reader of a road gleam to a stretcher.

13. Loosen the a coupling bolt also disconnect from the proof-reader an executive rod of manual updating of a road gleam.

14. Disconnect from the valve of the proof-reader hydraulic tubes. At once закупорьте the open ends of lines and reception ports of the valve in order to avoid hit in dirt system.

15. Turn out three bolts of fastening of basic arms of lines of communication in the left back corner of a stretcher.

16. Take a fastening clamp on a stretcher directing lines of communication. For отпускания a clamp beat out its central pin.

17. Disconnect tips of cables of a drive of a lay brake from executive levers of supports of brake mechanisms. Liberate covers of cables from bearing ledges on supports. Take assemblages of cables aside.
18. From both ends of a stretcher liberate hydraulic tubes from basic arms (separate from tubes flexible hoses, then liberate tubes from intermediate clamps on a stretcher) (address to the Head Brake system).
19. Turn a steering wheel against the stop to the left.
20. Attentively examine a stretcher and liberate from clamps on it all remained lines of communication (wires, hydraulic tubes and hoses (it is possible, it is necessary to make a detachment of some lines). Try to remember routes of a lining of all wires, hoses and tubes. At рассоединении штуцерных sockets be ready to gathering of a spilt liquid. At once cork the open ends of tubes/hoses and unions of their connection for the purpose of minimisation of losses of a hydraulic liquid and in order to avoid hit in dirt system.
21. Prop up a stretcher тележечным a jack through wooden брусок.

22. Turn out six fixing bolts and slightly lower a stretcher on a jack.



23. Last time make sure that no communication tenches disturb to stretcher removal.
24. Definitively lower a stretcher and take it from under the car.
25. At desire the bottom levers and a bar of the stabilizer of cross-section stability can be removed from a stretcher (corresponding sections see).

Installation

Installation is made upside-down. Pay attention to following moments:
   a) Where it is required, establish on a stretcher the bottom levers and a bar of the stabilizer of cross-section stability of a suspension bracket according to the instructions resulted in sections Removal, major repairs and installation of the bottom lever of a forward suspension bracket and Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket. Pay attention that the definitive tightening of fixture should be made only after stretcher installation on the car;
   b) At a corresponding complete set do not forget to replace sealing elements штуцерных connections of hydraulic lines;
   c) Remember that all самоконтрящиеся nuts are subject to replacement without fail;
   d) Track correctness of a lining and reliability of fastening of all lines of communication;
   e) do not forget to check up correctness of adjustment of a lay brake (address to the Head Brake system);
   f) After car lowering on the earth tighten спускной the gate of a regulator of pressure and translate a control lever a suspension bracket in position "Maximum";
   g) Check up level of a hydraulic liquid, in case of need make corresponding updating (address to the Head Routine maintenance);
   h) do not forget to pump over hydraulic system (address to the Head Brake system);
   i) In summary, make adjustment of height of a road gleam according to the instructions resulted in section Check of installation and adjustment of a road gleam, then tighten coupling bolts of collars of fastening of the proof-reader of a road gleam and (at a corresponding complete set) the gauge of movings of a body.


On the main page