Citroen Xantia

Since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
- Engine repair
   - The repair procedures which are not demanding extraction of the engine from the car - petrol engines
      Check компрессионного pressure in cylinders
      Fixing cranked / distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers газораспределительного a belt
      Belt of drive ГРМ - the general information, removal and installation
      Removal, check of a condition and installation натяжителя and cogwheels газораспределительного a belt
      Epiploon replacement (ов) a camshaft
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment клапанных backlashes
      Removal and installation of a head of cylinders
      Removal and pallet installation картера the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation маслоохладителя (models 2.0)
      Replacement of epiploons of a cranked shaft
      Removal, check of a condition and installation of a flywheel/privodnogo of a disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + The repair procedures which are not demanding extraction of the engine from the car - diesel engines
   + Removal and engine major repairs
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes

Removal, check of a condition and installation of the oil pump

Removal

 PERFORMANCE ORDER

1. Remove the pallet картера (Removal and pallet installation картера the engine see).
2. Give two screws and uncover asterisks with forward the pump parties.

3. Turn out three bolts of fastening of the pump to the basis of the block of cylinders/kartera of the engine. Liberate an asterisk from приводной chains and remove the pump. At a corresponding complete set remove also a remote plate established behind the pump.

Condition check

 PERFORMANCE ORDER

1. Attentively examine a pump asterisk on presence of signs of deterioration and mechanical damages. The special attention should be turned on сколы in the bases of teeths - in case of this sort of revealing of defects all assemblage of the pump is subject to replacement (in an individual order of an asterisk are not delivered). Simultaneously it is necessary to replace as well приводную a chain with a leading asterisk. For replacement of components of a drive of the oil pump remove a cogwheel of a cranked shaft (Removal, check of a condition and installation натяжителя and cogwheels газораспределительного a belt see). Отболтите from the block of cylinders the holder of an epiploon. Now the asterisk in gathering with a chain and the remote plug should be removed from a shaft pin (Removal and engine major repairs more in detail see).

2. Turn out three bolts of fastening of a cover of the mesh filter to the pump case. Uncover (at a corresponding complete set remove also маслоотражательную a plate).

3. Take a spring and the piston редукционного the valve from the nest in the pump case. Try to remember adjusting position of components.



4. Check up a condition a gear wheel and pump cases. In case of revealing of signs of excessive deterioration, задиров or other mechanical damages replace the pump in gathering.
5. Check up the piston редукционного the valve on presence of signs deterioration and mechanical damages, in case of need make replacement. The spring condition редукционного the valve can be estimated only by its comparison from the new. At the slightest doubts a spring will correctly replace. Both the piston, and a spring are delivered in an individual order.
6. Carefully wash out the mesh filter of the oil pump solvent and check up on presence of mechanical damages and signs of infringement of passableness. The defective filter is subject to replacement in gathering with a cover.
7. Lower a spring and the piston редукционного the valve in the landing nest in a cover of the mesh filter, then press last to the pump case, achieving combination of nests of the valve. At a corresponding complete set establish into place маслоотражательную a plate, screw bolts of fastening of a cover and strongly them tighten.

Installation

 PERFORMANCE ORDER

1. At a corresponding complete set establish into place a remote plate, then fill a pump asterisk in приводную a chain. Plant pump assemblage on the regular place in the basis of the block of cylinders/kartera of the engine. Screw fixing bolts and tighten them with demanded effort.
2. Where it is required, establish into place a cover of an asterisk of the pump, strongly having fixed its bolts.
3. Establish into place the pallet картера (Removal and pallet installation картера the engine see).
4. Before primary start of the engine it is necessary to fill assemblage of the pump by oil for what disconnect ECU systems of injection of fuel and turn the engine a starter until on an instrument guard the control lamp of pressure of oil will not go out. Do not forget to connect again electroconducting to ECU.



On the main page