Citroen Xantia

1. For the purpose of maintenance большего free space поддомкратьте redock of the car also establish it on props.
2. Check up rubber pillows of support of the power unit on presence of signs of hardening of a material and отслоения it from metal of arms. Defective support are subject to replacement.
3. Make sure of reliability of a tightening of fixture of support. Whenever possible take advantage динамометрическим of a key.
4. Having taken advantage as the lever of mount or the big screw-driver, estimate size люфта components of support. There where possibility of use of the lever is absent, ask the assistant to shake the unit in various directions, try to estimate visually люфт in support. Remember that some free wheeling of components is put in a design of support and defined by presence at them of flexible rubber pillows. The attention should be turned only on the excessive weak point appearing mainly as a result of easing of fixture, or owing to mechanical damages of metal arms.

1. Disconnect a negative wire from the battery. Liberate from intermediate clamps around a support arrangement all electric wires and hoses and take them aside, having released sufficient working space.
2. Get a jack under the engine, for loading distribution having laid between its head and the pallet картера wooden брусок. Cock a jack, having accepted on it weight of the unit and completely having unloaded a support.
3. Give three nuts of fastening of an arm of the right support to the engine block. Turn on also a unique nut of fastening of an arm to a rubber pillow of a support and remove an arm.
4. Remove a rubber buffer plate from a pillow hairpin, then turn out assemblage of a pillow from кузовного an element and remove from the car. In case of need the support arm can be отболчен from a wall of a head of cylinders and also is removed.
5. Attentively check up all components on presence of signs of deterioration and mechanical damages, defective details replace.
6. At assemblage screw pillow assemblage on the regular place in кузовной an element of the car and strongly tighten it. If removed, establish an arm on a head wall, slightly having greased fixing bolts with fixing hermetic and having tightened them with demanded effort.
7. Put on a rubber buffer plate a hairpin of a pillow and establish an arm.
8. Tighten with demanded effort of a nut of fastening of an arm.
9. Lower propping up engine a jack and take it from under the car. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery. Liberate from intermediate clamps around a support arrangement all electric wires and hoses and take them aside, having released sufficient working space.
2. Get a jack under the engine, for loading distribution having laid between its head and the pallet картера wooden брусок. Cock a jack, having accepted on it weight of the unit and completely having unloaded a support.
3. Give two bolts of fastening of the bent plate of fastening of a support to кузовному to an element. Remove a plate and take rubber демпфер from the top part of an arm of a support.
4. Turn on two nuts of bolts of fastening of an arm of the right support of the power unit to the engine. Also give a unique nut of fastening of an arm to a support pillow. Remove an arm.
5. Remove a rubber buffer plate from a support hairpin, then turn out assemblage of a pillow from кузовного an element and remove from the car. In case of need the support arm can be отболчен from a forward part of a head of cylinders and also is removed.
6. Attentively check up all components on presence of signs of deterioration and mechanical damages, defective details replace.
7. At assemblage screw pillow assemblage on the regular place in кузовной an element of the car and strongly tighten it. If removed, establish an arm on a forward wall of a head, having tightened with demanded effort fixing bolts.
8. Put on a rubber buffer plate a hairpin of a pillow and establish an arm.
9. Tighten nuts of fastening of an arm of a support with demanded effort, lower a jack and take it from under the car.
10. Enclose in the top part of an arm of a support rubber демпфер, then establish the bent fixing plate. Tighten bolts of fastening of a plate with demanded effort. Connect a negative wire to the battery.

1. Remove the battery and the pallet of its fastening in an impellent compartment (start and charge Systems see).
2. Get a jack under transmission, for loading distribution having laid on its head wooden брусок. Cock a jack, having accepted on it weight трансмиссионной assemblages.
3. Turn away the central nut of fastening a pillow of the left support of the unit, throw off a washer. Give nuts of fastening of a support and take last from an impellent compartment.
4. In case of need remove from a fixing hairpin the remote plug, then turn out a hairpin from the top plane картера transmissions and remove it together with a washer (if the hairpin is tightened too hardly, take advantage of a universal ex-tractor).
5. Attentively check up all components on presence of signs of deterioration and mechanical damages, defective details replace.
6. Clean a carving of a fixing hairpin and grease with its fixing hermetic. Screw a hairpin in the top part картера transmissions (do not forget about a washer) and tighten it with demanded effort.
7. At a corresponding complete set put on a hairpin the remote plug, then establish a pillow. Tighten bolts of fastening of a support to кузовному to an element and the central nut of fastening of a pillow with demanded effort. Lower a jack and take it from under the car.
8. Establish into place the battery pallet, strongly having tightened its fixture. Establish the battery (the engine Electric equipment see the Head).

1. Prop up противооткатными boots back wheels, then поддомкратьте redock of the car and establish it on props.

2. Turn out a bolt of fastening of a rack of a back support of the power unit to a back part of the block of cylinders.

3. Turn out a bolt of fastening of a rack to an arm on кузовном an element. Remove a rack.
4. For removal of assemblage of a support it is necessary to dismantle preliminary the right power shaft (Power shafts see the Head).
5. Having removed a power shaft, give fixing bolts and remove a support from a back part of the block of cylinders.
6. Attentively check up all components on presence of signs of deterioration and mechanical damages, defective details replace.
7. Establish support assemblage on the regular place on a back wall of the block of cylinders, tighten fixing bolts with demanded effort. Establish a power shaft (Power shafts see the Head).
8. Establish a rack of a support and tighten with demanded effort its fixture.
9. Lower the car on the earth.