Citroen Xantia

1. Remove a transmission (the Manual box of a gear change see), trace remove coupling assemblage (Coupling see the Head).

2. Block a gear wreath of a flywheel by means of the special adaptation, it is alternative приболтите a metal strip to a flywheel and the block of cylinders.

Do not try to fix at all a shaft by продевания a blocking core in drilling in its pulley (Fixing cranked/distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car see)!

3. Turn out bolts of fastening of a flywheel and remove last from a pin of a cranked shaft (the flywheel weighs much enough, - try not to drop it). If the directing pin is freely planted in the nest in an end face of a cranked shaft, take it and clean in a reliable place. At assemblage bolts of fastening of a flywheel are subject to replacement without fail.

1. Remove transmission (Automatic transmission see) Block приводной a disk in the same way that is offered for flywheel fixing (the subsection "the Flywheel (models with РКПП)", item 2) see here. Mark position drive a disk in relation to the rotation converter, then ослабьте all fixing bolts.
2. Turn out bolts and remove them together with a plate of the converter of rotation and two adjusting washers (on one from each of the parties of a plate of the converter). Pay attention that washers differ on a thickness, and thicker is established outside of a converter plate, and more thin - from within. Fastening bolts drive a disk are subject to replacement without fail.
3. Remove приводной a disk from a pin of a cranked shaft. If the directing pin is freely planted in the nest in an end face of a cranked shaft, take it and clean in a reliable place.

1. On models with РКПП attentively examine contacting to a coupling disk a working surface of a flywheel on presence of scratches and задиров. Make sure of absence having chopped off in the basis of teeths of a gear wreath. The working surface of a flywheel can be restored a way проточки, however replacement is more preferable. Do not hesitate to address for consultations to experts of the firm services-centres of company Citroyon. The gear wreath is not subject to shift and in case of its deterioration or damage also it is necessary to replace a flywheel.
2. On models with АТ check up приводной a disk of the converter of rotation on presence of signs of deformation, ниточных cracks around болтовых apertures, or going radially from the disk centre. Estimate degree of deterioration of a gear wreath and check up teeths on presence having chopped off. In case of this sort of revealing of defects приводной the disk is subject to replacement.

1. Carefully smooth out interfaced surfaces of a flywheel and a pin of a cranked shaft. Remove traces of old hermetic from carving apertures in an end face of a pin of a shaft (take advantage of a tap of the suitable size).

At absence of near at hand suitable tap, saw through lengthways a fixing bolt and take advantage of it for carving procleaning.

2. If the carving part of new bolts of fastening of a flywheel is not covered by fixing structure, grease with its hermetic approaching for this purpose.

3. Make sure available on the place of a pin of a shaft of a directing pin. Plant a flywheel on a pin and screw new fixing bolts.

4. Block a flywheel from проворачивания (the subsection "the Flywheel (models with РКПП)" see here, item 2) and tighten bolts of its fastening with demanded effort.

5. Establish into place coupling assemblage (Coupling see the Head). Remove the adaptation blocking a flywheel and establish into place a transmission (the Manual box of a gear change see).

1. Execute the procedures stated here in subsection "the Flywheel (models with РКПП)" in subitem 1-2 (with the amendment that deal not with a flywheel, and with приводным a disk).
2. Plant a disk on directing pin on a shaft pin.
3. Press a plate of the converter of rotation (thick washers outside). Achieve combination of the landing labels put in the course of dismantle.
4. Screw fixing bolts, block a shaft from проворачивания ("condition Check", item 1 see above) and tighten fixture with demanded effort.
5. Remove the adaptation blocking a disk and establish into place transmission (Automatic transmission see).