Citroen Xantia
+ Introduction
+ The operation manual
+ Routine maintenance
- Engine repair
- The repair procedures which are not demanding extraction of the engine from the car - petrol engines
Check компрессионного pressure in cylinders
Fixing cranked / distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car
Removal and installation of a cover of a head of cylinders
Removal and installation of a pulley of a cranked shaft
Removal and installation of covers газораспределительного a belt
Belt of drive ГРМ - the general information, removal and installation
Removal, check of a condition and installation натяжителя and cogwheels газораспределительного a belt
Epiploon replacement (ов) a camshaft
Removal, check of a condition and installation of a camshaft and pushers of valves
Check and adjustment клапанных backlashes
Removal and installation of a head of cylinders
Removal and pallet installation картера the engine
Removal, check of a condition and installation of the oil pump
Removal and installation маслоохладителя (models 2.0)
Replacement of epiploons of a cranked shaft
Removal, check of a condition and installation of a flywheel/privodnogo of a disk
Check of a condition and replacement of support of a suspension bracket of the power unit
+ The repair procedures which are not demanding extraction of the engine from the car - diesel engines
+ Removal and engine major repairs
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ Electric equipment schemes
|
Replacement of epiploons of a cranked shaft
The right epiploon
|
|
|
1. Remove a cogwheel of a cranked shaft and (at a corresponding complete set) the remote plug (Removal, check of a condition and installation натяжителя and cogwheels газораспределительного a belt see). Take away газораспределительный a belt aside from a working zone and fix it there in order to avoid pollution by oil. Measure and write down adjusting depth of landing of an epiploon in the casing.
|
|
2. Pierce, or drill in a face surface of an epiploon pair of small apertures and screw in them саморезы. Grasp heads of screws nippers and take an epiploon from the nest in a casing. Alternatively the epiploon can be taken a way поддевания a screw-driver with a flat sting - try not to damage a wall of a nest and a persistent coat hanger on a shaft pin. |
|
|
3. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to lead to failure of a new epiploon.
4. Grease sponges of a new epiploon with pure impellent oil, then accurately put on it a pin of a cranked shaft (sponges inside). Try not to damage soft sponges of an epiploon at its putting on on a pin.
5. By means of approaching оправки (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (item 1 see).
6. Collect rags surplus of oil and establish into place a cogwheel of a cranked shaft (Removal, check of a condition and installation натяжителя and cogwheels газораспределительного a belt see). |
|
The left epiploon
|
|
|
1. Remove a flywheel / приводной a disk (Removal, check of a condition and installation of a flywheel/privodnogo of a disk see). Measure and write down adjusting depth of landing of an epiploon in the casing.
2. Pierce, or drill in a face surface of an epiploon pair of small apertures and screw in them саморезы. Grasp heads of screws nippers and take an epiploon from the nest in a casing.
3. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to lead to failure of a new epiploon.
4. Grease sponges of a new epiploon with pure impellent oil, then accurately put on it a pin of a cranked shaft (sponges inside). Try not to damage soft sponges of an epiploon at its putting on on a pin.
5. By means of approaching оправки (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (item 1 see).
6. Collect rags surplus of oil and establish into place a flywheel/privodnoj a disk (Removal, check of a condition and installation of a flywheel/privodnogo of a disk see). |
|
|
On the main page
|