Subaru Legacy/Outback

1. Disconnect a negative wire from the battery and, before to start seat removal, wait not less than 20 seconds necessary for a discharge of the condenser of independent power supply SRS.

2. Having wrung out the clamp button, remove a headrest.

3. Incline a back forward.

4. Remove decorative covers of bolts of fastening from the forward and back party полозов a directing sled.

5. At a corresponding complete set disunite a yellow socket of the electroconducting of a lateral pillow of safety laid under a seat, also disconnect electroconducting of a thermoelectric element of heating of a seat and the gauge-switch of a control lamp «Fasten belts».

6. Turn out two back bolts of fastening of a directing sled.

7. Shift a seat against the stop back and turn out two forward bolts of fastening of the directing.

8. Lift a seat and take it from car salon, - try not to scratch a paint and varnish covering кузовных panels and not to tear a seat upholstery.

1. Disconnect a negative wire from the battery and, before to continue procedure performance, wait not less than 20 seconds necessary for a discharge of the condenser of independent power supply SRS.

2. Raise a seat and disunite a yellow socket of the electroconducting of a lateral pillow of safety laid under a seat, also disconnect electroconducting of a thermoelectric element of heating of a seat and the gauge-switch of a control lamp «Fasten belts».

3. Accurately take a seat from car salon, - try not to scratch a paint and varnish covering кузовных panels and not to tear a seat upholstery.

10. Remove an upholstery.
11. Remove подбивку seat backs.

12. At a corresponding complete set of the car liberate from intermediate clamps burn down electroconductings of a lateral pillow of safety.

13. Give two nuts equipped by protective caps and remove the module of a lateral pillow of safety (at a corresponding complete set of the car).

14. On seats with noncontrollable pillows remove the handle of the lever of adjustment of an inclination of a back and a lateral overlay of loopy assemblage.

15. On models with adjustable pillows turn out four loopy bolts and remove a seat pillow.

16. On models with noncontrollable pillows of seats turn out lateral bolts of fastening of a pillow and remove last from a frame.

17. Release spring clamps from the bottom party of a pillow of a seat and remove wire rings.

18. At a corresponding complete set of the car liberate from intermediate clamps electroconducting of a thermoelectric element of heating of a pillow.

19. Remove spring rings of fastening of an upholstery.

20. Remove an upholstery and подбивку seat pillows.

21. On models with adjustable pillows of a seat release spring clamps and remove handles of adjustment of height of position of a pillow of a seat.

22. On models with adjustable pillows of a seat remove the handle of the lever of adjustment of an inclination of a back of a seat.

23. On models with adjustable pillows turn out fixing bolts (preliminary remove decorative covers) and remove a lateral overlay of loopy assemblage.

24. On models with adjustable pillows remove подбивку pillows and a decorative overlay of a loopy spring.

25. On models with adjustable pillows turn out four fixing bolts and remove runners of a sled of a seat.

26. On models with noncontrollable pillows of seats turn out four fixing screws and remove loopy assemblages.

27. On models with noncontrollable pillows turn out four fixing bolts and remove runners of a sled.

28. Remove connecting electroconducting.

1. Release spring clamps from the bottom party of a pillow of a seat and remove wire rings.
2. At a corresponding complete set of the car liberate from intermediate clamps electroconducting of a thermoelectric element of heating of a pillow.
3. Remove spring rings of fastening of an upholstery, - the scheme of an arrangement of rings on pillows электроdrivers rings is identical to pillows with a fabric and leather upholstery.
4. Remove an upholstery and подбивку seat pillows.

5. Turn out the fixing screw and remove a back overlay.

6. On seats with a 8-item drive turn out the fixing screw and disconnect electroconducting from switch assemblage in the bottom part of an overlay of loopy assemblage, then remove an overlay.

7. On seats with a 6-item drive remove the handle of the lever of adjustment of an inclination of a back of a seat.

8. Remove an overlay established from the back party of a loop, then turn out two fixing bolts and remove loopy assemblage.

1. Assemblage is carried out in an order, the return to an order of dismantle of components, - try not to soil an upholstery and track smoothness of its landing.
2. On seats with a manual drive and a noncontrollable pillow track, that the internal loop has got in the correct image to an upholstery window.
3. Make sure of correctness of connection and reliability of fixing of contact sockets of electroconducting, track, that plaits have not appeared are jammed.
4. All fixture tighten with demanded effort (Specifications see).

2. With demanded effort (53 Nanometers) tighten four bolts of fastening of a sled.
3. Check up serviceability of functioning of the mechanism of adjustment of position of a seat.

3. Having lifted a back, take it from car salon.

6. Having pulled upwards, liberate from both sections of a back headrests.

7. Take clamps and remove forward section of the back carpet panel of a covering of a floor.

8. Having inclined both sections of a back, give loopy bolts/nuts.

9. Remove back assemblage.

1. Release located on perimetre of the back party of a back of a seat spring rings.

2. At a corresponding complete set give two fixing nuts and remove the central armrest.

3. Having dismantled spring rings, remove a back upholstery.

4. Release located on perimetre of the bottom party of a pillow of a seat spring rings.

5. Having dismantled spring rings, remove a pillow upholstery.

3. Rotating counter-clockwise, remove the back handle.

4. Having grasped a mouthpiece nippers, remove the plug of fixing of the directing probe of a headrest.

5. Remove a hook of fixing of a back.

6. Having liberated fixing tape, remove a back upholstery of a back.

7. Remove the bottom hook.

8. Release on four clamps.

9. Remove eight spring rings.

10. Remove with подбивки backs four forward spring rings.

11. Remove a back upholstery.

12. Turn out fixing bolts and remove loopy laths of a pillow of a seat.

13. Remove facing of a belt loop.

14. Take clamps and remove the bottom upholstery of a pillow.

15. Having dismantled a hook, remove a framework.

16. Having dismantled spring rings, remove an upholstery.

Assemblage is carried out in an order, the return to an order of dismantle of components, - try not to soil an upholstery and track smoothness of its landing.

1. Installation is made in an order, the return to an order of dismantle of components.

2. At installation of a back of a seat on models the Sedan at first plant it on the top hooks and only after tighten the bottom fixing bolts.

3. Track, that all fixture has been tightened with demanded effort.