Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
- Automatic transmission
Specifications
Electrohydraulic control system - the general information, appointment of basic elements
Self-diagnostics system - the general information and functioning principles
Diagnostics of general condition АТ
Problem diagnostics АТ
Removal and installation трансмиссионной assemblages
Replacement of elements of a suspension bracket трансмиссионной assemblages
Replacement of an epiploon of a casing of lengthening АТ
Condition check, adjustment and replacement of the gauge-switch of the permission of start
Removal and installation of the forward gauge of speed (VSS)
Removal and installation of the back gauge of speed (VSS)
Removal and installation of the gauge of turns of the turbine of the hydrotransformer
Removal, service and installation клапанной assemblages
Replacement of electromagnetic valves of switching, executive electromagnetic valves and the gauge of temperature ATF
Filter ATF replacement
Removal and installation of the module of management of transmission (TCM)
Removal, installation and check of a condition of lines of a path of cooling ATF
Removal, service and installation of components of the lever of selector AT
Removal, installation, check of a condition and adjustment drive selector AT cable
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Replacement of electromagnetic valves of switching, executive electromagnetic valves and the gauge of temperature ATF
|
1. Поддомкратьте the car also establish it on props. 2. Clear transmission outside. 3. Turn out a drain stopper and merge ATF then screw a stopper with demanded effort. 4. Remove the pallet картера. Take and carefully clear a magnet. Remove traces of a material of an old lining from interfaced surfaces of the pallet and картера transmissions. 5. Disunite contact sockets of executive electromagnetic valves and a socket of the gauge of temperature ATF. Liberate sockets from clamps. 6. Remove electromagnetic valves, working electromagnetic valves and the gauge of temperature ATF. |
|
The executive electromagnetic valve of the distributing device and клапанная assemblage of the distributing device
Details of installation of the executive electromagnetic valve and клапанной assemblages of the distributing device
|
1. Tyre out the car on the lift. 2. Disconnect a negative wire from the battery. 3. Remove an air cleaner/vozduhopriemnuju the chamber (see Has undressed Service of components of an inlet air path of the Head of the Power supply system and release).
4. Remove the rocking terminator (the Engine see the Head). 5. Remove reception and central sections of system of release of the fulfilled gases (see the Head of the Power supply system and release).
6. Remove assemblage of back section of system of release of the fulfilled gases with the muffler (see the Head of the Power supply system and release).
7. Lift the car and merge ATF, then screw a drain stopper and tighten it with demanded effort. 8. Uncover a thermofilter. 9. Remove карданный a shaft (Coupling see the Head). 10. Prop up АТ special трансмиссионным a jack, - track, that persistent plates of transmission did not rest against the pallet. 11. Remove a back cross-section beam of transmission. 12. Remove back VSS (see Has undressed Removal and installation of the back gauge of speed (VSS)).
|
13. Give a nut drive a selector cable. |
14. Shift приводной a cable so that access to bolts of fastening of the case of lengthening of transmission has opened. 15. Turn out fixing bolts and remove the lengthening case, - prepare in advance drain capacity for reception of a liquid containing in the case. 16. Disconnect electroconducting from the executive electromagnetic valve of the distributing device. 17. Remove the executive electromagnetic valve and the case клапанной assemblages of the distributing device. 18. Installation is made upside-down. Track, that all fixture has been tightened with demanded effort. After installation of the case of lengthening adjust a selector cable (see Has undressed Removal, installation, check of a condition and adjustment drive selector AT cable). In summary add in transmission fresh ATF, having finished its level to the middle of a "cold" scale measuring probeа. |
|
|
On the main page
|